The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft assembly removal/installation are shown below.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
1.REMOVE FRONT WHEEL
51420
2.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25A-FXS: Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS: Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
53737D
3.REMOVE FRONT FENDER APRON SEAL LH
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25A-FXS: Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS: Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
53736E
4.REMOVE FRONT FENDER APRON SEAL RH
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25A-FXS: Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS: Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
5.DRAIN TRANSAXLE OIL
for Automatic Transaxle: Click hereGeneral>MAINTENANCE>UB80E AUTOMATIC TRANSAXLE FLUID>REPLACEMENT
for Manual Transaxle: Click hereGeneral>MAINTENANCE>EG62 MANUAL TRANSAXLE OIL>REPLACEMENT
for CVT: Click hereGeneral>MAINTENANCE>K120 CONTINUOUSLY VARIABLE TRANSAXLE FLUID>REPLACEMENT
for Hybrid Vehicle Transaxle: Click hereGeneral>MAINTENANCE>P710 HYBRID TRANSAXLE FLUID>REPLACEMENT
43502H
6.REMOVE FRONT AXLE SHAFT NUT LH
43501H
7.REMOVE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
48810
8.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
9.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
48069
10.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
11.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
12.DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH
Remove the bolt and disconnect the front speed sensor and front flexible hose from the front shock absorber assembly.
Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.
Remove the bolt, disengage the clamp and disconnect the front speed sensor from the front shock absorber assembly and steering knuckle.
Prevent foreign matter from contacting the sensor tip.
Be careful not to damage the front speed sensor.
Clean the speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.
| *a | Matchmark |
Put matchmarks on the front drive shaft assembly and front axle hub sub-assembly.
Do not use a punch to make the matchmarks.
Using a plastic hammer, disconnect the front drive shaft assembly from the steering knuckle with axle hub.
Be careful not to damage the boot and drive shaft dust cover.
Do not excessively push out the drive shaft from the front axle hub.
13.DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH
Use the same procedure described for the LH side.
43420
14.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
Using SST, remove the front drive shaft assembly LH.
Do not damage the front drive shaft oil seal LH, front axle inboard joint boot and front drive shaft dust cover LH.
Do not drop the front drive shaft assembly LH.
When carrying the front drive shaft assembly LH, hold it horizontally.
43410
15.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
Disconnect the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
Do not damage the front drive shaft oil seal RH, transfer case oil seal RH, front axle inboard joint boot and front drive shaft dust cover RH.
Do not drop the front drive shaft assembly RH.
When carrying the front drive shaft assembly RH, hold it horizontally.
Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.
43420G
16.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
Using a screwdriver, remove the front drive shaft hole snap ring LH.