The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.
After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD
65351A
4.REMOVE BATTERY HOLE COVER
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
58441J
6.REMOVE BATTERY SERVICE HOLE COVER
G3834
7.REMOVE SERVICE PLUG GRIP
8.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
9. DISCHARGE FUEL SYSTEM PRESSURE
10. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
11.SECURE STEERING WHEEL
12.REMOVE FRONT WHEELS
53896B
13.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
Remove the 3 screws.
Detach the clip and remove the front fender front splash shield LH.
53895B
14.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
Remove the 3 screws.
Detach the clip and remove the front fender front splash shield RH.
51441
15.REMOVE NO. 1 ENGINE UNDER COVER
Remove the 2 bolts and 10 screws.
Detach the guide and remove the No. 1 engine under cover.
|
Bolt |
|
Screw |
51420
16.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
|
Bolt |
|
Screw |
|
Clip |
Remove the 2 bolts, 2 screws, 6 clips and No. 2 engine under cover assembly.
53737D
17.REMOVE FRONT FENDER APRON SEAL LH
|
Bolt |
|
Clip |
Remove the 2 bolts, clip and front fender apron seal LH.
53736E
18.REMOVE FRONT FENDER APRON SEAL RH
|
Bolt |
|
Clip |
Remove the 2 bolts, clip and front fender apron seal RH.
19.REMOVE FRONT BUMPER ASSEMBLY
20.REMOVE HEADLIGHT ASSEMBLY LH
52618
21.REMOVE FRONT LOWER BUMPER ABSORBER
Remove the clip.
Detach the claws and remove the front lower bumper absorber.
52132A
22.REMOVE FRONT BUMPER NO. 2 REINFORCEMENT
23.DRAIN ENGINE COOLANT (for Engine)
24.DRAIN ENGINE OIL
25.DRAIN HYBRID TRANSAXLE FLUID
12601B
26.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
for LHD:
Lift the front of the No. 1 engine cover sub-assembly to detach the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to detach the clip and remove the No. 1 engine cover sub-assembly.
Attempting to detach both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.
for RHD:
Lift the front of the No. 1 engine cover sub-assembly to detach the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to detach the clip and remove the No. 1 engine cover sub-assembly.
Attempting to detach both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.
17750A
27.REMOVE INLET AIR CLEANER ASSEMBLY
28.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
G9200
29.REMOVE INVERTER WITH CONVERTER ASSEMBLY
G92A0A
30.REMOVE INVERTER RESERVE TANK ASSEMBLY
| *1 | No. 2 Inverter Cooling Hose |
| *2 | No. 5 Inverter Cooling Hose |
| *a | Pin |
| *b | Grommet |
|
Bolt |
|
Clip |
Remove the 2 bolts.
Detach the pin and remove the inverter reserve tank assembly.
Slide the 2 clips and disconnect the No. 2 inverter cooling hose and No. 5 inverter cooling hose from the inverter reserve tank assembly.
16282
31.REMOVE NO. 5 WATER BY-PASS HOSE
Slide the 2 clips and remove the No. 5 water by-pass hose from the No. 3 water by-pass pipe and radiator assembly.
23826
32.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Detach the clamp.
Disconnect the No. 1 fuel vapor feed hose from the purge VSV.
23901
33.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp from the fuel tube connector.
Click hereEngine / Hybrid System>A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
Disconnect the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
87246
34.DISCONNECT OUTLET HEATER WATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to detach the lock claws and pull off the outlet heater water hose from the No. 2 water by-pass pipe sub-assembly.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.
87245
35.DISCONNECT INLET HEATER WATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to detach the lock claws and pull off the inlet heater water hose from the flow shutting valve (water by-pass hose assembly).
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector with plastic bags to prevent damage and contamination.
16571C
36.DISCONNECT NO. 1 RADIATOR HOSE
Detach the clamp.
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16572D
37.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet.
88711
38.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
88704
39.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
G9229A
40.DISCONNECT NO. 5 INVERTER COOLING HOSE
Slide the clip and disconnect the No. 5 inverter cooling hose from the motor cooling cooler.
41.DISCONNECT WIRE HARNESS
After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.
Detach the claws and remove the No. 2 relay block cover.
|
Nut |
|
Connector |
Remove the nut from the engine room relay block and junction block assembly.
Disconnect the connectors from the engine room relay block and junction block assembly.
Using a screwdriver, detach the claw and disconnect the wire harness from the engine room relay block and junction block assembly.
Detach the clamp.
Remove the 2 bolts and disconnect the ground wires.
51468B
42.REMOVE ENGINE UNDER COVER HEAT INSULATOR
Remove the 2 clips and engine under cover heat insulator.
58166A
43.REMOVE FRONT FLOOR COVER LH
|
Bolt |
|
Screw |
|
Clip |
Remove the 2 bolts, 4 screws and clip.
Detach the clips and remove the front floor cover LH.
58165C
44.REMOVE FRONT FLOOR COVER RH
|
Bolt |
|
Screw |
|
Clip |
Remove the 2 bolts, 3 screws and clip.
Detach the clips and remove the front floor cover RH.
17410
45.REMOVE FRONT EXHAUST PIPE ASSEMBLY
43502H
46.REMOVE FRONT AXLE SHAFT NUT LH
43501H
47.REMOVE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
89543
48.DISCONNECT FRONT SPEED SENSOR LH
89542
49.DISCONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
50.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
51.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
45470
52.DISCONNECT TIE ROD ASSEMBLY LH
45460
53.DISCONNECT TIE ROD ASSEMBLY RH
Use the same procedure described for the LH side.
48069
54.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
55.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
43420
56.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
for 4WD/AWD:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for 4WD/AWD)>REMOVAL
43410
57.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
for 4WD/AWD:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for 4WD/AWD)>REMOVAL
45220
58.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
59.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
|
Attachments | - | - |
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
|
Bolt |
|
Nut |
Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the 3 bolts and the engine mounting stay LH from the engine mounting insulator sub-assembly LH.
Remove the 4 bolts and separate the engine mounting insulator sub-assembly LH from the hybrid vehicle transaxle assembly.
| *1 | Front Bumper Extension Sub-assembly LH |
| *2 | Front Bumper Extension Sub-assembly RH |
| *3 | Rear Front Suspension Member Brace LH |
| *4 | Rear Front Suspension Member Brace RH |
|
Bolt |
|
Nut |
Remove the 2 bolts (A), 2 bolts (B), 4 nuts and front bumper extension sub-assembly LH and front bumper extension sub-assembly RH from the front frame assembly and vehicle body.
Remove the 2 bolts (C), 4 bolts (D) and rear front suspension member brace LH and rear front suspension member brace RH from the front frame assembly and vehicle body.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
23825
60.REMOVE FUEL DELIVERY GUARD
Remove the bolt and fuel delivery guard from the engine mounting bracket RH.
61.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
11361J
62.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover from the cylinder block sub-assembly.
51100H
63.REMOVE FRONT FRAME ASSEMBLY
12361
64.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>REMOVAL
82715
65.REMOVE WIRING HARNESS CLAMP BRACKET
for LHD:
Detach the clamps and disconnect the engine wire.
Remove the bolt and wiring harness clamp bracket.
for RHD:
Detach the clamp and disconnect the engine wire.
Remove the bolt and wiring harness clamp bracket.
12371A
66.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
for LHD:
Detach the clamp and disconnect the engine wire.
Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.
for RHD:
Detach the clamp and disconnect the engine wire.
Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.
82121
67.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
821H2
68.REMOVE HV AIR CONDITIONING WIRE
Detach the clamps.
| *a | Green-colored Lock |
|
Slide |
Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.
Make sure to wear insulated gloves.
Insulate the disconnected terminals and connector with insulating tape.
for 2WD:
Remove the bolt.
Detach the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.
for 4WD/AWD:
Remove the 2 bolts.
Detach the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.
28193
69.REMOVE STARTER HOLE INSULATOR
11363A
70.REMOVE FLYWHEEL HOUSING SIDE COVER
30900
71.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
31270
72.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
13405
73.REMOVE FLYWHEEL SUB-ASSEMBLY
19315
74.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
75.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
76.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.
G921A
77.REMOVE NO. 1 INVERTER RESERVE TANK BRACKET
Remove the bolt and No. 1 inverter reserve tank bracket.
12305
78.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
| *1 | Suction Pipe Sub-assembly |
| *2 | Air Conditioning Tube And Accessory Assembly |
Disconnect the connector.
Detach the clamps and disconnect the suction pipe sub-assembly and air conditioning tube and accessory assembly.
|
No. 6 Water By-pass Hose |
|
Bolt |
|
Nut |
Disconnect the No. 6 water by-pass hose and detach the clamp.
Remove the bolt and nut.
Detach the clamps and remove the radiator reserve tank assembly.
Remove the bolt and disconnect the No. 2 ground wire.
|
Bolt |
|
Nut |
Remove the 2 bolts and nut and remove the engine mounting insulator sub-assembly RH.
12341
79.REMOVE ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Remove the 2 bolts and engine mounting spacer from the vehicle body.
89661
80.REMOVE ECM
12306
81.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.
Remove the bolt.
Detach the claw and disconnect the engine room main wire.
|
Bolt |
|
Nut |
Remove the 2 bolts, nut and the engine mounting insulator sub-assembly LH.