Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING › from 2019.02
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377756 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.



PROCEDURE

Hide 75766B 1.INSTALL REAR DOOR WINDOW FRAME MOULDING LH (REAR PILLAR SIDE)

a.

Attach the guide to temporarily install the rear door window frame moulding LH (rear pillar side) to the rear door frame.

B524096


b.

Using an air riveter or hand riveter with a nose piece, install the rear door window frame moulding LH (rear pillar side) with 4 new φ4.0 mm (0.157 in.) waterproof rivets.

NOTICE:
·
B171664C27
1.229,1.042 1.083,1.573 1.083,1.573 1.271,2.281 false 1.083,1.573 0.813,1.573 false 1.75,0.833 2.031,1.583 2.031,1.583 1.74,2.521 false 2.031,1.573 2.313,1.573 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.594,1.479 0.781,1.677 0.188,0.198 10 false *1 2.354,1.5 2.542,1.677 0.188,0.177 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

·
B172390C28
2.325,0.536 2.513,0.713 0.189,0.177 10 *a 2.325,1.527 2.5,1.705 0.175,0.177 10 *a 2.434,2.73 2.634,2.907 0.2,0.177 10 *b 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.223,2.477 0.181,0.153 10 *1 1.043,1.044 1.223,1.196 0.181,0.153 10 *1 1.043,0.0040 1.223,0.157 0.181,0.153 10 *1 0.818,2.402 1.018,2.402 false
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the rear door window frame moulding LH (rear pillar side).

·

Do not tilt the riveter when installing the rivet to the rear door window frame moulding LH (rear pillar side).

·

Do not leave any space between the rivet head and rear door window frame moulding LH (rear pillar side).

·
B172391C27
2.304,0.996 2.504,1.173 0.2,0.177 10 *a 2.408,2.434 2.62,2.612 0.211,0.177 10 *b 0.978,0.515 1.173,0.686 0.195,0.171 10 *1 0.735,0.603 0.941,0.603 false 0.973,2.023 1.182,2.194 0.209,0.171 10 *1 0.731,2.111 0.937,2.111 false
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the rear door window frame moulding LH (rear pillar side) and rear door panel. Firmly hold together the 2 items while installing the rivet.



HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.



Hide 75764A 2.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH

a.

Attach the guide to temporarily install the rear door upper window frame moulding LH to the rear door frame.

B524097


b.

Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding LH with 3 new φ4.0 mm (0.157 in.) waterproof rivets.

NOTICE:
·
B171664C27
1.229,1.042 1.083,1.573 1.083,1.573 1.271,2.281 false 1.083,1.573 0.813,1.573 false 1.75,0.833 2.031,1.583 2.031,1.583 1.74,2.521 false 2.031,1.573 2.313,1.573 false 2.271,0.542 2.469,0.74 0.198,0.198 10 false *a 2.271,2.385 2.49,2.583 0.219,0.198 10 false *b 0.594,1.479 0.781,1.677 0.188,0.198 10 false *1 2.354,1.5 2.542,1.677 0.188,0.177 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

·
B172390C28
2.325,0.536 2.513,0.713 0.189,0.177 10 *a 2.325,1.527 2.5,1.705 0.175,0.177 10 *a 2.434,2.73 2.634,2.907 0.2,0.177 10 *b 0.72,0.066 1.023,0.066 false 0.818,1.11 1.018,1.11 false 1.043,2.324 1.223,2.477 0.181,0.153 10 *1 1.043,1.044 1.223,1.196 0.181,0.153 10 *1 1.043,0.0040 1.223,0.157 0.181,0.153 10 *1 0.818,2.402 1.018,2.402 false
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the rear door upper window frame moulding LH.

·

Do not tilt the riveter when installing the rivet to the rear door upper window frame moulding LH.

·

Do not leave any space between the rivet head and rear door upper window frame moulding LH.

·
B172391C27
2.304,0.996 2.504,1.173 0.2,0.177 10 *a 2.408,2.434 2.62,2.612 0.211,0.177 10 *b 0.978,0.515 1.173,0.686 0.195,0.171 10 *1 0.735,0.603 0.941,0.603 false 0.973,2.023 1.182,2.194 0.209,0.171 10 *1 0.731,2.111 0.937,2.111 false
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the rear door upper window frame moulding LH and rear door panel. Firmly hold together the 2 items while installing the rivet.



HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.



Hide 67846A 3.INSTALL REAR DOOR FRONT OUTSIDE SEAL LH

a.
B524099C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door front outside seal LH.


Hide 75762B 4.INSTALL REAR DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

HINT:

When installing a new rear door window frame moulding LH (center pillar side), heat the rear door panel and rear door window frame moulding LH (center pillar side) using a heat light.


Heating Temperature
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Door Window Frame Moulding LH (Center Pillar Side) 20 to 30°C (68 to 86°F)

CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door panel and rear door window frame moulding LH (center pillar side) excessively.


a.

Clean the rear door panel surface.

i.

Using a heat light, heat the rear door panel surface.


ii.

Remove any double-sided tape from the rear door panel.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the rear door window frame moulding LH (center pillar side) with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.


·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.





b.

Install a new rear door window frame moulding LH (center pillar side).

i.

Using a heat light, heat the rear door panel and rear door window frame moulding LH (center pillar side).


ii.

Remove the release paper from the rear door window frame moulding LH (center pillar side).

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.
B524100C01
0.917,1.677 1.573,1.448 true 0.729,1.635 0.917,1.813 0.188,0.177 10 true *a
*a Double-sided Tape
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and clip and attach the double-sided tape and caulking sponge to install the rear door window frame moulding LH (center pillar side).

HINT:

Press the rear door window frame moulding LH (center pillar side) firmly to install it.




c.

Remove the protective tape.


Hide 67872 5.INSTALL REAR DOOR WEATHERSTRIP LH

a.
B524173

Attach the clip and install the rear door weatherstrip LH.


b.

Install the clip.


c.
B524245C01
1.24,1.26 1.552,1.458 0.313,0.198 10 false *a 1.24,2.271 1.552,2.469 0.313,0.198 10 false *b
*a Correct
*b Incorrect


Check that the rear door weatherstrip LH is securely installed to the rail of the rear door upper window frame moulding LH as shown in the illustration.

NOTICE:

If the rear door weatherstrip LH is not securely installed, water may leak into the vehicle.



Hide 68104 6.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 68124C 7.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

Hide 67408E 8.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68152C 9.INSTALL REAR DOOR GLASS RUN LH

Hide 75722A 10.INSTALL REAR DOOR BELT MOULDING LH

Hide 67674A 11.INSTALL REAR DOOR FRAME GARNISH LH

Hide 67842E 12.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 68199 13.INSTALL REAR DOOR REAR BELT SEAL LH

Hide 68174A 14.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

Hide 67604 15.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 16.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 74646A 17.INSTALL DOOR ASSIST GRIP COVER LH

Hide 69278C 18.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL




d.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 65351A 20.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 21.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 22.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 23. INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 24. CHECK POWER WINDOW CONTROL SYSTEM

Hide 25. CHECK POWER DOOR LOCK CONTROL SYSTEM