Home › Vehicle Exterior › WINDOW / GLASS › HEATED WINDSHIELD DEFROSTER SYSTEM (for HV Model) › from 2019.02
RM3620E _59 Vehicle Exterior _076527 WINDOW / GLASS _0390391 HEATED WINDSHIELD DEFROSTER SYSTEM(for HV Model) J

WINDOW / GLASS  HEATED WINDSHIELD DEFROSTER SYSTEM(for HV Model)  Heated Windshield Defroster System does not operate  


DESCRIPTION

When the front window deicer switch is operated, an activation request signal is sent to the air conditioning control assembly through the direct line. The air conditioning control assembly sends an operation request signal to the air conditioning amplifier assembly via LIN communication, and when the air conditioning amplifier assembly receives the operation request signal, the system turns on the HWD relay (HDW NO.1), HWD relay (HWD NO.2), HWD relay (HWD NO.3) and operates the heated windshield defroster system.

WIRING DIAGRAM

E409112E02
2.625,0.125 4.042,0.396 1.417,0.271 10 false from IG1 NO.1 Relay 1.073,0.302 2.115,0.49 1.042,0.188 10 false ECU-IG1 NO.3 1.427,0.698 1.74,0.896 0.313,0.198 10 false IG 3.094,0.698 3.25,0.896 0.156,0.198 10 false D 3.094,1 3.25,1.198 0.156,0.198 10 false E 4.135,0.802 4.594,1 0.458,0.198 10 false SWC 1.344,1.594 3.302,1.896 1.958,0.302 10 false Front Window Deicer Switch 3.896,1.594 5.427,1.979 1.531,0.385 10 false Air Conditioning Control Assembly 4.135,1.094 4.594,1.292 0.458,0.198 10 false SW3 4.927,0.948 5.542,1.146 0.615,0.198 10 false LIN1 6,0.948 6.615,1.146 0.615,0.198 10 false LIN1 2.458,2.646 3.375,2.844 0.917,0.198 10 false DEICER 0.292,2.458 1.708,2.74 1.417,0.281 10 false from Auxiliary Battery 0.313,2.885 1.656,3.104 1.344,0.219 10 false from IG1 NO.1 Relay 2.24,3.094 3.271,3.354 1.031,0.26 10 false ECU-IG1 NO.3 3.313,3.271 4.177,3.677 0.865,0.406 10 false HWD Relay (HWD NO.3) 6.01,2.917 6.625,3.115 0.615,0.198 10 false FDEF 5.552,3.708 7.115,4.104 1.563,0.396 10 false Air Conditioning Amplifier Assembly 0.573,8.51 2.333,8.74 1.76,0.229 10 false : LIN Communication Line 1.448,4.333 1.604,4.531 0.156,0.198 10 false B 1.458,6.177 1.615,6.375 0.156,0.198 10 false B 1.448,4.865 1.604,5.063 0.156,0.198 10 false E 1.458,6.719 1.615,6.917 0.156,0.198 10 false E 2.656,5.344 3.5,5.729 0.844,0.385 10 false HWD Relay (HWD NO.1) 2.646,7.208 3.458,7.667 0.813,0.458 10 false HWD Relay (HWD NO.2) 3.813,4.656 5.042,4.854 1.229,0.198 10 false HWD NO.1 3.781,6.458 5.01,6.656 1.229,0.198 10 false HWD NO.2 5.396,4.458 6.979,4.708 1.583,0.25 10 false from Auxiliary Battery 0.333,7.906 1.458,8.125 1.125,0.219 10 false Windshield Glass 1.333,1.438 1.948,1.635 0.615,0.198 10 false G113 3.344,0.698 3.5,0.896 0.156,0.198 10 false 4 3.333,1 3.49,1.198 0.156,0.198 10 false 2 1.208,0.688 1.365,0.885 0.156,0.198 10 false 5 3.885,0.698 4.073,0.896 0.188,0.198 10 false 11 3.885,1 4.042,1.198 0.156,0.198 10 false 3 4.24,2.354 4.396,2.552 0.156,0.198 10 false 3 3.208,2.354 3.365,2.552 0.156,0.198 10 false 5 4.229,2.802 4.385,3 0.156,0.198 10 false 2 3.219,2.813 3.375,3.01 0.156,0.198 10 false 1 2.51,4.844 2.667,5.042 0.156,0.198 10 false 2 2.51,6.74 2.667,6.938 0.156,0.198 10 false 2 2.51,4.365 2.667,4.563 0.156,0.198 10 false 3 2.5,6.167 2.656,6.365 0.156,0.198 10 false 3 3.531,4.354 3.688,4.552 0.156,0.198 10 false 5 3.531,6.177 3.688,6.375 0.156,0.198 10 false 5 3.531,4.865 3.688,5.063 0.156,0.198 10 false 1 3.531,6.729 3.688,6.927 0.156,0.198 10 false 1 5.542,3.531 6,3.729 0.458,0.198 10 false G46 5.74,2.802 6.052,3 0.313,0.198 10 false 22 3.896,1.438 4.354,1.635 0.458,0.198 10 false G24 1.74,6.302 2.354,6.5 0.615,0.198 10 false A58 1.813,4.76 1.969,4.958 0.156,0.198 10 false 1 1.823,4.271 1.979,4.469 0.156,0.198 10 false 2 1.833,6.094 1.99,6.292 0.156,0.198 10 false 2 1.823,6.635 1.979,6.833 0.156,0.198 10 false 1 0.323,5.25 1.51,5.635 1.188,0.385 10 false Heated Windshield Defroster RH 0.281,7.083 1.469,7.469 1.188,0.385 10 false Heated Windshield Defroster LH 1.74,4.479 2.198,4.677 0.458,0.198 10 false A57 1.74,4.979 2.198,5.177 0.458,0.198 10 false A57 1.74,6.844 2.354,7.042 0.615,0.198 10 false A58 5.396,6.281 6.979,6.531 1.583,0.25 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the ambient temperature is 5°C (41°F) or higher, or if a malfunction of the ambient temperature sensor (thermistor assembly) is detected, the HWD NO.1, HWD NO.2 or HWD NO.3 relays will be deactivated and the front window deicer switch indicator light will blink.



PROCEDURE

1.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:

Both the heated windshield defroster system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.


OK:

The air conditioning system operates normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
HWD Relay Windshield glass (heated windshield defroster) OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
HWD Relay
50004 121 102
OK:

The heated windshield defroster system operates normally.



Result:
Result Proceed to
OK A
NG (Neither heated windshield defroster LH nor heated windshield defroster RH does not warm up.) B
NG (Only heated windshield defroster LH does not warm up.) C
NG (Only heated windshield defroster RH does not warm up.) D



A

3.INSPECT FRONT WINDOW DEICER SWITCH

B

7.INSPECT HWD RELAY (HWD NO.3)

C

12.INSPECT HWD RELAY (HWD NO.2)

D

16.INSPECT HWD RELAY (HWD NO.1)
3.INSPECT FRONT WINDOW DEICER SWITCH

OK

4.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - BATTERY)

NG

4.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - BATTERY)
a.
E380278C05
1.49,0.219 1.958,0.438 0.469,0.219 1.948,1.385 2.521,0.792 2.521,0.792 2.74,0.792 true 0.073,0.031 0.385,0.188 0.313,0.156 10 false *a 1.563,0.25 1.979,0.458 0.417,0.208 10 false G113 2.833,0.698 3.146,0.896 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Front Window Deicer Switch)


Disconnect the front window deicer switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G113-5 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - AIR CONDITIONING CONTROL ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - AIR CONDITIONING CONTROL ASSEMBLY AND BODY GROUND)
a.

Disconnect the G113 front window deicer switch connector.


b.

Disconnect the G24 air conditioning control assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-2 (E) - G24-3 (SW3) Always Below 1 Ω
G113-4 (D) - G24-11 (SWC) Always Below 1 Ω
G113-2 (E) or G24-3 (SW3) - Body ground Always 10 kΩ or higher
G113-4 (D) or G24-11 (SWC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY
a.

Replace the air conditioning control assembly with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL


b.

Check that the heated windshield defroster system operates normally.

OK:

The heated windshield defroster system operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

7.INSPECT HWD RELAY (HWD NO.3)
a.

Remove the HWD relay (HWD NO.3) from the No. 2 engine room relay block.


b.

Inspect the HWD relay (HWD NO.3).

Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - BATTERY)

NG

REPLACE HWD RELAY (HWD NO.3)

8.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - BATTERY)
a.

Remove the HWD relay (HWD NO.3) from the No. 2 engine room relay block assembly.


b.
E409127C01
0.094,0.052 0.406,0.208 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to HWD Relay [HWD NO.3])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
HWD relay (HWD NO.3) holder terminal-5 - Body ground Ignition switch off 11 to 14 V
HWD relay (HWD NO.3) holder terminal-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the HWD relay (HWD NO.3) from the No. 2 engine room relay block assembly.


b.

Disconnect the G46 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.3) holder terminal-2 - G46-22 (FDEF) Always Below 1 Ω
HWD relay (HWD NO.3) holder terminal-2 or G46-22 (FDEF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.1])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.1])
a.

Remove the HWD relay (HWD NO.3) and HWD relay (HWD NO.1) from the No. 2 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.3) holder terminal-3 - HWD relay (HWD NO.1) relay holder terminal-1 Always Below 1 Ω
HWD relay (HWD NO.3) relay holder terminal-3 - Body ground Always 10 kΩ or higher
HWD relay (HWD NO.1) holder terminal-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.2])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.2])
a.

Remove the HWD relay (HWD NO.3) and HWD relay (HWD NO.2) from the No. 2 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.3) holder terminal-3 - HWD relay (HWD NO.2) relay holder terminal-1 Always Below 1 Ω
HWD relay (HWD NO.3) relay holder terminal-3 - Body ground Always 10 kΩ or higher
HWD relay (HWD NO.2) holder terminal-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT HWD RELAY (HWD NO.2)
a.

Remove the HWD relay (HWD NO.2) from the No. 2 engine room relay block.


b.

Inspect the HWD relay (HWD NO.2).

Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.2] - BATTERY AND BODY GROUND)

NG

REPLACE HWD RELAY (HWD NO.2)

13.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.2] - BATTERY AND BODY GROUND)
a.

Remove the HWD relay (HWD NO.2) from the No. 2 engine room relay block assembly.


b.
E409126C01
0.083,0.042 0.396,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to HWD relay [HWD NO.2])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
HWD relay (HWD NO.2) holder terminal-5 - Body ground Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.2) holder terminal-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.2])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.2])
a.

Remove the HWD relay (HWD NO.3) and HWD relay (HWD NO.2) from the No. 2 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.3) holder terminal-3 - HWD relay (HWD NO.2) holder terminal-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER LH] - HWD RELAY [HWD NO.2] AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER LH] - HWD RELAY [HWD NO.2] AND BODY GROUND)
a.

Disconnect the A58 windshield glass (heated windshield defroster LH) connector.


b.

Remove the HWD relay (HWD NO.2) from the No. 2 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-2 (B) - HWD relay (HWD NO.2) relay holder terminal-3 Always Below 1 Ω
A58-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS (HEATED WINDSHIELD DEFROSTER LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT HWD RELAY (HWD NO.1)
a.

Remove the HWD relay (HWD NO.1) from the No. 2 engine room relay block.


b.

Inspect the HWD relay (HWD NO.1).

Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.1] - BATTERY AND BODY GROUND)

NG

REPLACE HWD RELAY (HWD NO.1)

17.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.1] - BATTERY AND BODY GROUND)
a.

Remove the HWD relay (HWD NO.1) from the No. 2 engine room relay block assembly.


b.
E409126C01
0.083,0.042 0.396,0.198 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to HWD relay [HWD NO.1])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
HWD relay (HWD NO.1) holder terminal-5 - Body ground Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.1) holder terminal-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.1])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (HWD RELAY [HWD NO.3] - HWD RELAY [HWD NO.1])
a.

Remove the HWD relay (HWD NO.3) and HWD relay (HWD NO.1) from the No. 2 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD relay (HWD NO.3) holder terminal-3 - HWD relay (HWD NO.1) holder terminal-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER RH] - HWD RELAY [HWD NO.1] AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER RH] - HWD RELAY [HWD NO.1] AND BODY GROUND)
a.

Disconnect the A57 windshield glass (heated windshield defroster RH) connector.


b.

Remove the HWD relay (HWD NO.1) from the No. 2 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-2 (B) - HWD relay (HWD NO.1) relay holder terminal-3 Always Below 1 Ω
A57-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS (HEATED WINDSHIELD DEFROSTER RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR