Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR › from 2019.02
RM3620E _53 Suspension _076491 REAR SUSPENSION _0372238 REAR STABILIZER BAR A

REAR SUSPENSION  REAR STABILIZER BAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear stabilizer bar removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FXS w/ Canister Pump Module:

(Click here)

·

for A25A-FXS w/o Canister Pump Module:

(Click here)

·

for A25B-FXS:

(Click here)



Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FKS w/ Canister Pump Module:

(Click here)

·

for A25A-FKS w/o Canister Pump Module:

(Click here)

·

for M20A-FKS:

(Click here)



CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 58327B 3.REMOVE MAIN MUFFLER HEAT INSULATOR

a.
C403777

Remove the 4 nuts and main muffler heat insulator from the vehicle body.


Hide 53896B 4.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 5.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51420 7.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 58166A 8.REMOVE FRONT FLOOR COVER LH (w/ Floor Under Cover)

Hide 58166A 9.REMOVE FRONT FLOOR COVER RH (w/ Floor Under Cover)

Hide 58399D 10.REMOVE NO. 2 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 58398F 11.REMOVE NO. 1 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 48738C 12.REMOVE LOWER NO. 2 CONTROL ARM COVER LH (w/ Cover)

Hide 48737C 13.REMOVE LOWER NO. 2 CONTROL ARM COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the LH side.


Hide 48840A 14.REMOVE REAR STABILIZER LINK ASSEMBLY LH

a.
C403436N01
1.281,0.083 1.438,0.281 0.156,0.198 10 true A 2.24,1.792 2.396,1.99 0.156,0.198 10 true B

Loosen the nut (A) of the rear stabilizer link assembly LH.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



b.

Loosen the nut (B) of the rear stabilizer link assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



c.
C403182C01
1.75,1.833 2,1.833 false 1.917,2.25 2.167,2.25 false 2.042,1.771 2.292,2.021 0.25,0.25 10 false *a 2.208,2.188 2.542,2.438 0.333,0.25 10 false *b
*a Wooden Block
*b Jack
V100155

Wooden Block Placement Location


Using a jack and wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C403436

Remove the bolt, 2 nuts and rear stabilizer link assembly LH.


Hide 48830D 15.REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 16.REMOVE REAR STABILIZER BAR

a.
C403437

Remove the 4 bolts, rear stabilizer bar, rear No. 1 stabilizer bar bracket LH, rear No. 1 stabilizer bar bracket RH, rear No. 2 stabilizer bar bracket LH, rear No. 2 stabilizer bar bracket RH and 2 rear stabilizer bushings from the rear suspension member sub-assembly.


Hide 48835 17.REMOVE REAR LOWER STABILIZER BRACKET

a.
C403438

Remove the 2 rear lower stabilizer brackets from the rear stabilizer bushing.


Hide 48832A 18.REMOVE REAR NO. 1 STABILIZER BAR BRACKET LH

a.
C403439

Remove the rear No. 1 stabilizer bar bracket LH from the rear stabilizer bushing.


Hide 48832A 19.REMOVE REAR NO. 1 STABILIZER BAR BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48818 20.REMOVE REAR STABILIZER BUSHING

a.
C403440

Remove the 2 rear stabilizer bushings from the rear stabilizer bar.