Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster) › 2019.02–2020.05
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1241  Low or High Power Supply Voltage  C1242  Open Circuit in IG1/IG2 Power Source Circuit  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake booster with master cylinder assembly) power source voltage drops, or there is insufficient voltage to operate the ABS main relay, the skid control ECU (brake booster with master cylinder assembly) will store these DTCs.

These DTCs may also be stored if the auxiliary battery voltage drops below 9.5 V.

HINT:

DTC C1256 (Accumulator Low Pressure) may also be memorized if there is a drop in power source voltage.


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1241 Low or High Power Supply Voltage 101
102
551
552
553
·

INF Code: 101

-

Any of the following is detected when the BS terminal voltage is 9.3 V or less:

(1)

Vehicle not decelerated (brake pedal is not depressed) for 3 seconds or more.

(2)

While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A.

(3)

Vehicle decelerated (brake pedal is depressed) for 0.06 seconds.



·

INF Code: 102

-

Any of the following is detected when the ECU internal voltage is 6.8 V or less:

(1)

With the power switch off, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command.

(2)

With the power switch off and the IG1 terminal voltage 9.5 V or less, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command.

(3)

Sensor supply voltage is 4.75 V or less, or 5.25 V or more for 0.06 seconds.

(4)

Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more for 0.06 seconds.



·

INF Code: 551

-

When driving at 3 km/h (1.9 mph) or more, IG1 terminal voltage is 9.5 V or less, or VM1 voltage is 8.6 V or less for 10 seconds or more.


·

INF Code: 552

-

When VM1 voltage is 8.6 V or less, sensor supply voltage is low for 60 seconds or more.


·

INF Code: 553

-

VM1 voltage is 16.6 V or more for 0.8 seconds.



·

Improperly connected connector, deformation or corrosion of terminals

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (Brake booster with master cylinder assembly)


-
C1242 Open Circuit in IG1/IG2 Power Source Circuit 111
112
·

INF Code: 111

-

Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V higher than) for 4 seconds or more.


·

INF Code: 112

-

While hybrid vehicle control ECU assembly communication is enabled, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously for 4 seconds or more.

-

When the vehicle speed exceeds 10 km/h, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously for 4 seconds or more.



·

INF Code: 111

-

Open or short in IG1 circuit

-

Improperly connected connector, deformation or corrosion of terminals

-

Entry and start system (for start function, HV Model)

-

Auxiliary battery

-

Hybrid control system (Charging circuit)

-

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 112

-

Open or short in IG2 circuit

-

Improperly connected connector, deformation or corrosion of terminals

-

Entry and start system (for start function, HV Model)

-

Auxiliary battery

-

Hybrid control system (Charging circuit)

-

Skid control ECU (Brake booster with master cylinder assembly)



-

DTC Detection Conditions: C1241 INF Code: 101
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition BS terminal voltage is 9.3 V or less ○ ○ ○
Malfunction Status Vehicle not decelerated (brake pedal is not depressed) ○ - -
While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A - ○ -
Vehicle decelerated (brake pedal is depressed) - - ○
Detection Time 3 seconds or more - 0.06 seconds
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1241 INF Code: 102
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition ECU internal voltage is 6.8 V or less ○ ○ ○ ○
Malfunction Status With the power switch off, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command ○ - - -
With the power switch off and the IG1 terminal voltage 9.5 V or less, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command - ○ - -
Sensor supply voltage is 4.75 V or less, or 5.25 V or more - - ○ -
Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more - - - ○
Detection Time - - 0.06 seconds 0.06 seconds
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1242 INF Code: 112
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status While hybrid vehicle control ECU assembly communication is enabled, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously ○ -
When the vehicle speed exceeds 10 km/h, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously - ○
Detection Time 4 seconds or more 4 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C279472E25
0.583,0.802 2,0.969 1.417,0.167 10 false from Auxiliary Battery 0.969,1.99 2.385,2.156 1.417,0.167 10 false from IG Circuit 0.979,2.594 2.188,2.917 1.208,0.323 10 false from IG Circuit 3.938,0.969 5.135,1.146 1.198,0.177 10 false ABS NO. 2 3.948,1.563 5.104,1.74 1.156,0.177 10 false ABS NO. 1 3.833,2.156 4.844,2.365 1.01,0.208 10 false ECU-IG1 NO.2 3.979,2.771 5.438,3.094 1.458,0.323 10 false ECU-IG2 NO.3 5.938,0.813 6.188,0.979 0.25,0.167 10 false BI 5.938,1.406 6.188,1.573 0.25,0.167 10 false BS 5.938,2 6.188,2.167 0.25,0.167 10 false IG1 5.938,2.594 6.188,2.76 0.25,0.167 10 false IG2 5.927,3.198 6.344,3.365 0.417,0.167 10 false GND 5.927,4.333 6.344,4.5 0.417,0.167 10 false GND3 5.927,3.76 6.344,3.927 0.417,0.167 10 false GND2 5.927,4.927 6.344,5.094 0.417,0.167 10 false GND4 5.927,5.51 6.344,5.677 0.417,0.167 10 false GND5 5.927,6.083 6.344,6.25 0.417,0.167 10 false GND6 4.698,7.042 5.115,7.208 0.417,0.167 10 false A42 5.063,7.042 7.156,7.375 2.094,0.333 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.635,0.708 5.885,0.875 0.25,0.167 10 false 14 5.635,1.302 5.885,1.469 0.25,0.167 10 false 15 5.635,1.896 5.885,2.063 0.25,0.167 10 false 16 5.635,2.5 5.885,2.667 0.25,0.167 10 false 12 5.635,3.094 5.885,3.26 0.25,0.167 10 false 28 5.635,3.656 5.885,3.823 0.25,0.167 10 false 27 5.635,4.219 5.885,4.385 0.25,0.167 10 false 26 5.635,4.823 5.885,4.99 0.25,0.167 10 false 25 5.635,5.406 5.885,5.573 0.25,0.167 10 false 24 5.635,5.99 5.885,6.156 0.25,0.167 10 false 23

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ENTRY AND START SYSTEM (for start function, HV Mode)
a.

Check if entry and start system (for start function, HV Model) DTCs are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>DTC CHECK / CLEAR

Body Electrical > Smart Access > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK HYBRID CONTROL SYSTEM

B

3.CHECK DTC
a.

Check that no main relay malfunction DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Main relay malfunction DTCs are not output. A
Main relay malfunction DTCs are output. B



A

4.CHECK AUXILIARY BATTERY

B

4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C316493C40
0.208,0.729 0.594,0.99 0.385,0.26 1.323,1.865 0.875,2.823 true 2.615,1.865 2.167,2.823 true 2.885,1.104 2.458,1.698 true 1.875,1.104 2.271,1.698 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.281,0.781 0.74,0.979 0.458,0.198 10 false A42 0.719,2.875 1.177,3.073 0.458,0.198 10 false IG1 2.052,2.854 2.51,3.052 0.458,0.198 10 false BS 2.948,0.99 3.26,1.177 0.313,0.188 10 false BI 1.625,1 2.083,1.198 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-14 (BI) - Body ground Always 11 to 14 V
A42-15 (BS) - Body ground Always 11 to 14 V
A42-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V
A42-12 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C316493C41
0.208,0.729 0.594,0.99 0.385,0.26 2.458,1.854 2.01,2.771 true 2.625,2.042 2.625,2.854 true 2.344,1.854 1.313,2.896 true 2.688,1.094 2.26,1.792 true 1.927,1.073 2.156,1.792 true 0.802,2.719 2.063,1.833 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.281,0.781 0.74,0.979 0.458,0.198 10 false A42 2.49,2.885 2.948,3.083 0.458,0.198 10 false GND 1.823,2.823 2.281,3.021 0.458,0.198 10 false GND2 1.052,2.938 1.51,3.135 0.458,0.198 10 false GND3 2.729,0.969 3.167,1.135 0.438,0.167 10 false GND4 1.521,0.927 1.958,1.094 0.438,0.167 10 false GND5 0.542,2.75 1,2.948 0.458,0.198 10 false GND6
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-28 (GND) - Body ground Always Below 1 Ω
A42-27 (GND2) - Body ground Always Below 1 Ω
A42-26 (GND3) - Body ground Always Below 1 Ω
A42-25 (GND4) - Body ground Always Below 1 Ω
A42-24 (GND5) - Body ground Always Below 1 Ω
A42-23 (GND6) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.



c.

Turn the power switch off.


d.

Turn the power switch on (READY).


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1241 and C1242 are not output. A
DTCs C1241 and/or C1242 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE




A

B