The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. DISABLE BRAKE CONTROL
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55704B
4.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY
for A25A-FXS:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25A-FXS)>REMOVAL
for A25B-FXS:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25B-FXS)>REMOVAL
5.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
73900
6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
87211
7.REMOVE NO. 1 AIR DUCT
84340
8.REMOVE STOP LIGHT SWITCH ASSEMBLY
47101A
9.REMOVE BRAKE PEDAL RETURN SPRING
10.SEPARATE WIRE HARNESS
Disconnect the connector from the brake pedal stroke sensor assembly.
Disengage the 2 clamps to separate the wire harness from the brake pedal support assembly.
47264A
11.REMOVE PUSH ROD PIN
47220D
12.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
Remove the 2 nuts and separate the brake master cylinder reservoir assembly.
47235G
13.DISCONNECT NO. 2 RESERVOIR HOSE
Slide the clip and disconnect the No. 2 reservoir hose from the brake booster with master cylinder assembly.
47234L
14.DISCONNECT NO. 1 RESERVOIR HOSE
Slide the clip and disconnect the No. 1 reservoir hose from the brake booster with master cylinder assembly.
44571A
15.DISCONNECT NO. 1 BRAKE ACTUATOR HOSE
Slide the clip and disconnect the brake actuator hose from the brake master cylinder reservoir assembly.
16.REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH RESERVOIR HOSE
Remove the brake master cylinder reservoir with reservoir hose
47233
17.REMOVE RESERVOIR BRACKET
Remove the bolt, 2 nuts and reservoir bracket.
44551C
18.SEPARATE NO. 1 BRAKE ACTUATOR TUBE
Remove the 2 nuts and separate the No. 1 brake actuator tube from the vehicle body.
47314
19.DISCONNECT NO. 4 FRONT BRAKE TUBE
Using a union nut wrench, disconnect the No. 4 front brake tube.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
47210L
20.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
|
Release the lock lever |
|
Disconnect the connector |
Disengage the clamp to separate the wire harness.
Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.
Be careful not to allow brake fluid to enter the removed connector.
| *a | To Front Wheel Cylinder LH |
| *b | To Rear Wheel Cylinder RH |
| *c | To Brake Booster Pump Assembly |
| *d | To Rear Wheel Cylinder LH |
| *e | To Front Wheel Cylinder RH |
Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.
Use tags or make a memo to identify the places to reconnect.
Disengage the 8 clamps to remove the 2 brake tube clamps from the brake lines.
Disengage the 4 clamps to remove the brake tube clamp from the brake lines.
Disengage the clamp and remove the brake tube clamp from the vehicle body.
Disengage the clamp to remove the No. 4 front brake tube with brake tube clamp from the brake line.
Disengage the clamp to remove the brake tube clamp from the No. 4 front brake tube.
| *1 | Connector Portion |
| *2 | Union |
| *3 | Push Rod Clevis |
| *4 | Boot |
| *5 | Front No. 2 Brake Tube |
Remove the 4 nuts and brake booster with master cylinder assembly.
Do not kink or damage the brake lines.
Do not carry the brake booster with master cylinder assembly by the portion shown in the illustration.
44785C
21.REMOVE BRAKE BOOSTER GASKET