The skid control ECU (brake booster with master cylinder assembly) stores and corrects the individual differences in the brake pedal stroke sensor assembly, actuator solenoids, and stroke simulator solenoid. Perform initialization and calibration of the linear solenoid valve if any of these parts is replaced.
The skid control ECU (brake booster with master cylinder assembly) receives the shift position P signal from the hybrid vehicle control ECU assembly through the CAN communication system.
These DTCs are cleared when the linear valve offset learning results are normal.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1345 | Linear Solenoid Valve Offset Learning undone | - | Linear valve offset learning undone. | Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. | - |
| C1368 | Linear Solenoid Valve Offset | - | Offset learned value out of specification. | ·
Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. ·
Brake actuator (Brake booster with master cylinder assembly) |
- |
When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
When C1451 is output together with C1345 and/or C1368, inspect and repair the trouble areas indicated by C1451 first.
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check the DTCs (electronically controlled brake system and hybrid control system) that are output.
for Electronically Controlled Brake System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR
for Hybrid Control System (for 2WD): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>DTC CHECK / CLEAR
for Hybrid Control System (for 4WD/AWD): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs (except C1345, C1368 and hybrid control system DTCs) are not output. | A |
| Hybrid control system DTCs are output. | B |
| DTCs (except C1345 and/or C1368) are output. | C |
Before performing initialization and calibration of the linear solenoid valve, C1203 will be output.
A
B
for 2WD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
for 4WD/AWD: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
C
Turn the power switch off.
Perform initialization and calibration of the linear solenoid valve.
| Tester Display |
|---|
| ECB Utility |
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch off.
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C1345 and C1368 are not output. | A |
| DTCs C1345 and/or C1368 are output. | B |
A
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD without Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD without Vacuum Brake Booster)>REMOVAL