Home › Brake › BRAKE (FRONT) › FRONT BRAKE (for 2-Pot Caliper) › from 2019.02
RM3620E _54 Brake _076409 BRAKE (FRONT) _0372102 FRONT BRAKE(for 2-Pot Caliper) A

BRAKE (FRONT)  FRONT BRAKE(for 2-Pot Caliper)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC. (for HV Model)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C405064C01
2.063,0.969 2.885,0.969 true 2.063,1.052 2.396,1.052 2.396,1.052 2.396,0.969 true 2.958,0.885 3.125,1.042 0.167,0.156 10 true *a
*a Matchmark


Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.
C405063

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
for Steel Steering Knuckle : 107 N*m (1091 kgf*cm, 79 ft.*lbf)
for Aluminum Steering Knuckle : 150 N*m (1530 kgf*cm, 111 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C405075C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a thin layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 47715A 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C405076C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a thin layer of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (lower side).


b.

Install a new front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (lower side).


c.
C405077C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a thin layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the 2 front disc brake cylinder slide pins.


d.

Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder mounting.


e.

Push each front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 5.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.
C405142

Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.



Hide 04945 6.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 7.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.

·

Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.




b.
C405078

Install the 2 anti-squeal springs to the front disc brake pads.

NOTICE:
·

When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.




Hide 47750 8.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the front disc brake cylinder assembly while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.

·

Be sure that the anti-squeal springs are installed to the front disc brake pads.




Hide 47313J 9.CONNECT FRONT FLEXIBLE HOSE

a.
C397703

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.



Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



c.

Perform the following procedure if air bleeding is not necessary:

i.

Turn the power switch on (READY).


ii.

Depress the brake pedal and release it.




Hide 11.BLEED BRAKE LINE

Hide 12.INSTALL FRONT WHEEL