Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID (w/o Vacuum Brake Booster) › from 2019.02
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377032 BRAKE FLUID(w/o Vacuum Brake Booster) N

BRAKE SYSTEM (OTHER)  BRAKE FLUID(w/o Vacuum Brake Booster)  BLEEDING  


CAUTION / NOTICE / HINT

CAUTION:

The GTS must be used for air bleeding. If not used, the air bleeding will be incomplete, which is hazardous and may lead to an accident.


NOTICE:
·

Perform air bleeding with the shift lever in P selected and the parking brake applied.

·

As brake fluid may overflow when bleeding, do not place the fluid can on the reservoir filler opening.

·

Perform air bleeding while maintaining the brake fluid level between the MAX and MIN lines on the brake fluid reservoir.

·

Air bleeding will be difficult if the following occurs:

(a)

The brake actuator hose (the hose between the brake booster pump assembly and brake master cylinder reservoir assembly) is higher than the fluid level and air enters the hose.

(b)

During the air bleeding procedure, air enters the brake booster pump assembly while the pump motor is operating.


·

While performing air bleeding, the accumulator pressure drop may cause a buzzer to sound. As there is no problem, continue with air bleeding.

·

During air bleeding, DTCs for pressure sensor malfunctions, etc. may be stored. After air bleeding and if instructed in the procedures, clear the DTCs.

·

Release the parking brake while the linear valve offset calibration procedure.

·

Do not allow brake fluid on any painted vehicle body surface. If brake fluid leaks onto any painted surface, immediately wash it off.

·

When bleeding air, select the suitable procedure according to the table below.

Replaced/Installed Item Work Procedure
Flexible hose (front/rear) Bleed brake line
Disc brake cylinder assembly (front/rear)
Brake booster pump assembly Bleed brake system
Brake booster with master cylinder assembly
Brake master cylinder reservoir assembly



HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.BLEED BRAKE LINE

a.

Remove the center cowl top ventilator louver.

i.
C400729

Disengage the 3 hooks and separate the hood to cowl top seal from the cowl top ventilator louver sub-assembly.


ii.
C400733

Disengage the 2 claws and 2 guides to remove the center cowl top ventilator louver from the cowl top ventilator louver sub-assembly.



b.

Fill the reservoir with brake fluid.

i.
C400750

Remove the brake master cylinder reservoir filler cap assembly.


ii.

Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT3 or SAE J1704 or FMVSS No. 116 DOT4




c.

Bleed the brake line.

i.

Connect the GTS to the DLC3 and turn the power switch on (IG).


ii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Air Bleeding
50005 105 125

iii.

Select "Usual air bleeding", and bleed air from the brake fluid following the instructions on the GTS.


iv.

After air bleeding, tighten each bleeder plug.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)



vi.

Turn the GTS off and turn the power switch off.



d.

Inspect for brake fluid leaks.


e.

Install the brake master cylinder reservoir filler cap.


f.

Install the center cowl top ventilator louver.

i.

Engage the 2 claws and 2 guides to install the center cowl top ventilator louver to the cowl top ventilator louver sub-assembly.


ii.

Engage the 3 hooks and install the hood to cowl top seal to the cowl top ventilator louver sub-assembly.



Hide 2.BLEED BRAKE SYSTEM

a.

Remove the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL



c.
C400748

Wait for at least 2 minutes with the power switch off, and disconnect the reservoir level switch connector.

NOTICE:

Do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.


HINT:

This procedure is not required if the reservoir level switch connector has been disconnected.



d.

Fill the reservoir with brake fluid.

i.
C400750

Remove the brake master cylinder reservoir filler cap assembly.


ii.

Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT3 or SAE J1704 or FMVSS No. 116 DOT4




e.

Bleed the brake system.

i.

Connect the GTS to the DLC3 and turn the power switch on (IG).


ii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Air Bleeding
50005 105 125

iii.

Select "ABS actuator has been replaced", and bleed air from the brake fluid following the instructions on the GTS.

NOTICE:

Before following the instructions on the GTS to perform linear valve offset calibration, release the parking brake. When calibration is complete, immediately apply the parking brake.



iv.
C400752C01
1.813,1.125 2.427,1.698 2.427,1.698 2.667,1.698 true 2.75,1.615 3.146,1.865 0.396,0.25 10 false *a
*a Stroke Simulator Bleeder Plug


After air bleeding, tighten each bleeder plug.

Torque:
Front Bleeder Plug : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Rear Bleeder Plug : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Stroke Simulator Bleeder Plug : 8.5 N*m (87 kgf*cm, 75 in.*lbf)

HINT:

The stroke simulator bleeder plug is positioned as shown in the illustration.




vi.

Turn the GTS off and turn the power switch off.



f.

Install the brake master cylinder reservoir filler cap.


g.

Connect the reservoir level switch connector.


h.

Inspect for brake fluid leaks.



j.

Install the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION