Home › Drivetrain › EG62 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY › from 2019.09
RM3620E _52 Drivetrain _076270 EG62 MANUAL TRANSMISSION / TRANSAXLE _0371321 MANUAL TRANSAXLE ASSEMBLY A

EG62 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release with bearing cylinder assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 35150D 1.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat the O-ring of a new transmission case plug assembly with gear oil.


b.

Install the transmission case plug assembly to the manual transaxle assembly.


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C405659


Hide 335A0 3.INSTALL CONTROL CABLE BRACKET ASSEMBLY

a.

Install the control cable bracket assembly to the manual transaxle assembly with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 31485 4.INSTALL CLUTCH FLEXIBLE HOSE BRACKET

a.

Install the clutch flexible hose bracket to the manual transaxle assembly with the bolt.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 31482F 5.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY TO BLEEDER TUBE

Hide 31407B 6.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31400 7.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31488F 8.INSTALL BLEEDER TO FLEXIBLE HOSE TUBE

Hide 30300 9.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.
C405604C01
0.479,1.115 0.708,1.115 0.708,1.115 1.042,0.656 true 2.396,0.406 2.771,1 2.771,1 2.979,1 true 0.271,1.031 0.479,1.281 0.208,0.25 10 false *1 3,0.917 3.25,1.146 0.25,0.229 10 false *1
*1 Knock Pin


Check that the 2 knock pins are installed on the engine assembly before installing the manual transaxle assembly.


b.

Align the input shaft with the clutch disc and install the manual transaxle assembly to the engine assembly.


c.
C410214N01
1.146,0.031 1.302,0.229 0.156,0.198 10 false A 2.75,0.323 2.906,0.521 0.156,0.198 10 false B 2.365,0.083 2.521,0.281 0.156,0.198 10 false C 0.729,0.813 0.885,1.01 0.156,0.198 10 false E 0.917,1.625 1.073,1.823 0.156,0.198 10 true E 1.167,1.979 1.323,2.177 0.156,0.198 10 false E 2.479,1.969 2.635,2.167 0.156,0.198 10 false D 2.781,1.625 2.938,1.823 0.156,0.198 10 false E

Temporarily install the bolt A.

HINT:

Bolt A: Install from the manual transaxle assembly side.



d.

Install the bolt B.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

HINT:

Bolt B: Install from the manual transaxle assembly side.



e.

Install the bolt C, then fully tighten the bolt A.

Torque:
for bolt C : 64 N*m (653 kgf*cm, 47 ft.*lbf)
for bolt A : 46 N*m (469 kgf*cm, 34 ft.*lbf)

HINT:

Bolt C: Install from the manual transaxle assembly side.



f.

Install the bolt D.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Bolt D: Install from the manual transaxle assembly side.



g.

Install the 4 bolts E.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the engine assembly when installing it to the manual transaxle assembly.

·

Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.

·

Make sure that the knock pins fit securely into the holes when installing the manual transaxle assembly to the engine assembly.

·

Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.



HINT:

Bolt E: Install from the engine assembly side.



Hide 11363A 11.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 12303 12.INSTALL REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.

Install the rear No. 2 engine mounting bracket to the rear engine mounting bracket with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
C405665C01
1.875,0.26 2.031,0.458 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the rear engine mounting bracket sub-assembly to the manual transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (A) → Tighten bolt (C)



Hide 12371A 13.INSTALL REAR ENGINE MOUNTING INSULATOR

a.
C405660C01
2.604,2.354 2.75,2.083 2.75,2.083 2.917,2.083 false 2.948,1.979 3.219,2.188 0.271,0.208 10 false *a
*a Rubber Protrusion


Install the rear engine mounting insulator to the rear engine mounting bracket sub-assembly with the bolt and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Align the rubber protrusion of the rear engine mounting insulator with the shape of the rear engine mounting bracket sub-assembly.



b.
C405662C01
1.344,0.146 1.5,0.344 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B


Install the 2 wire harness clamp brackets to the rear engine mounting insulator with the 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12311A 14.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C405664C01
1.292,0.167 1.448,0.365 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the transverse engine engine mounting bracket to the manual transaxle assembly with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



Hide 12361 15.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the front transverse engine engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 12372A 16.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

a.

Install the transverse engine engine mounting insulator to the manual transaxle assembly with the 5 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 17.CONNECT WIRE HARNESS

a.

Connect the wire harness to the manual transaxle assembly.

i.
C405600C01
0.385,0.406 0.542,0.604 0.156,0.198 10 false -
V100135

Bolt
V100136

Back-up Light Switch Assembly Connector


Attach the 4 clamps.


ii.

Connect the back-up light switch assembly connector and install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.
C405599C01
0.5,0.667 0.656,0.865 0.156,0.198 10 false -
V100135

Nut
V100136

Bolt
V100137

Engine Coolant Temperature Sensor Connector


Connect the engine coolant temperature sensor connector.


iv.

Install the 2 nuts and bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


v.
C405598C01
1.323,0.135 1.49,0.344 0.167,0.208 10 false -
V100135

Nut
V100136

Neutral Position Switch Connector
V100137

Transmission Revolution Sensor Connector


Connect the neutral position switch connector and transmission revolution sensor connector.


vi.

Install the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


vii.
C405597

Attach the clamp and install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 19.CONNECT WIRE HARNESS (for RHD)

Hide 20.CONNECT WIRE HARNESS (for LHD)

Hide 45319 21.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 25.INSTALL ENGINE ASSEMBLY WITH MANUAL TRANSAXLE ASSEMBLY