The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Map light assembly ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
DCM (telematics transceiver)* ·
Harness or connector |
*: w/ Telematics Transceiver and for 6 Speakers
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
When replacing the DCM (telematics transceiver), make sure to replace it with a new one. (w/ Telematics Transceiver)
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Telematics Transceiver and for 6 Speakers | A |
| w/o Telematics Transceiver or w/ Telematics Transceiver and for 9 Speakers | B |
A
B
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P14-4 (SNS2) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P20-6 (SNS2) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H6 DCM (telematics transceiver) connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - P14-5 (MCO-) | Always | Below 1 Ω |
| H6-35 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - P20-7 (MCO-) | Always | Below 1 Ω |
| H6-35 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(DCM [Telematics Transceiver]) |
Remove the DCM (telematics transceiver) with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G2 radio and display receiver assembly connector.
Disconnect the P14*1 or P20*2 map light assembly connector.
*1: for TMMR Made
*2: except TMMR Made
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P14-4 (SNS2) | Always | Below 1 Ω |
| G2-22 (MIN-) - P14-5 (MCO-) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-25 (SNS2) - P20-6 (SNS2) | Always | Below 1 Ω |
| G2-22 (MIN-) - P20-7 (MCO-) | Always | Below 1 Ω |
| G2-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| G2-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *A | except TMMR Made |
| *B | for TMMR Made |
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (SNS2) - 5 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except TMMR Made |
| *B | for TMMR Made |
| *a | Component without harness connected
(Map Light Assembly) |
| *b | Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side]) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (SNS2) - C-1 (SNS2) | Always | Below 1 Ω |
| 6 (MCO-) - C-2 (MIC-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (SNS2) - C-1 (SNS2) | Always | Below 1 Ω |
| 5 (MCO-) - C-2 (MIC-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG