Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY) › from 2020.05
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0425052 HYBRID CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD with LITHIUM-ION BATTERY)  P0A3011  Drive Motor "B" Temperature Sensor Circuit Short to Ground  P0A3015  Drive Motor "B" Temperature Sensor Circuit Short to Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the rear motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU assembly malfunction
·

Hybrid vehicle control ECU assembly internal malfunction


Rear motor temperature sensor malfunction
·

Internal rear motor temperature sensor malfunction

·

Open or short in rear motor temperature sensor


Wire harness between the rear motor temperature sensor and hybrid vehicle control ECU assembly
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the rear motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the rear motor (MGR) becomes high. If the self-protection function does not operate, the rear motor (MGR) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

The resistance of the thermistor built into the rear motor temperature sensor changes in accordance with changes in the rear motor temperature. The lower the rear motor temperature, the higher the thermistor resistance. Conversely, the higher the rear motor temperature, the lower the resistance.

C189867E17
0.76,2.104 0.885,2.302 0.125,0.198 10 false 0 2,2.875 3.406,3.094 1.406,0.219 10 false Temperature (°C (°F)) 0.885,2.375 1.083,2.573 0.198,0.198 10 false 10 1.26,2.375 1.458,2.573 0.198,0.198 10 false 15 2.406,2.375 2.604,2.573 0.198,0.198 10 false 30 2.792,2.375 2.99,2.573 0.198,0.198 10 false 35 1.646,2.375 1.844,2.573 0.198,0.198 10 false 20 2.021,2.375 2.219,2.573 0.198,0.198 10 false 25 0.677,1.521 0.875,1.719 0.198,0.198 10 false 50 0.594,0.948 0.865,1.146 0.271,0.198 10 false 100 3.146,2.375 3.344,2.573 0.198,0.198 10 false 40 0.063,0.5 1.26,0.771 1.198,0.271 10 false Resistance (kΩ) 0.865,2.542 1.208,2.74 0.344,0.198 10 false (50) 1.229,2.552 1.573,2.75 0.344,0.198 10 false (59) 1.615,2.552 1.958,2.75 0.344,0.198 10 false (68) 1.979,2.563 2.323,2.76 0.344,0.198 10 false (77) 2.385,2.573 2.729,2.771 0.344,0.198 10 false (86) 2.771,2.583 3.115,2.781 0.344,0.198 10 false (95) 3.063,2.583 3.406,2.781 0.344,0.198 10 false (104)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A3011 Drive Motor "B" Temperature Sensor Circuit Short to Ground Short to ground in the rear motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU assembly

·

Rear motor temperature sensor (Rear traction motor with transaxle assembly)


Does not come on Master Warning: Comes on
P0A3015 Drive Motor "B" Temperature Sensor Circuit Short to Battery or Open Open or short to +B in the rear motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU assembly

·

Rear motor temperature sensor (Rear traction motor with transaxle assembly)


Does not come on Master Warning: Comes on

Related Data List
DTC No. Data List
P0A3011 Rear Motor Temperature
P0A3015

HINT:

After confirming that DTC P0A3011 or P0A3015 is output, use the GTS to check "Rear Motor Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With the power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C414356E01
5.375,2.667 5.833,2.865 0.458,0.198 10 false A29 5.375,2.865 7.104,3.271 1.729,0.406 10 false Hybrid Vehicle Control ECU Assembly 0.073,2.667 0.385,2.865 0.313,0.198 10 false O2 0.063,2.844 2.26,3.406 2.198,0.563 10 false Rear Traction Motor with Transaxle Assembly (Rear Motor Temperature Sensor) 3.542,2.25 4,2.448 0.458,0.198 10 false AN1 2.438,2.531 2.896,2.729 0.458,0.198 10 false ON1 2.438,2.708 3.208,3.104 0.771,0.396 10 false Frame Wire Connector 3.542,2.406 5.26,2.615 1.719,0.208 10 false No. 2 Floor Wire Connector 1.219,1.813 1.833,2.01 0.615,0.198 10 false RMTG 1.313,0.646 1.771,0.844 0.458,0.198 10 false RMT 5.406,0.656 5.865,0.854 0.458,0.198 10 false RMT 5.385,1.823 6,2.021 0.615,0.198 10 false RMTG 5.115,1.844 5.427,2.042 0.313,0.198 10 false 43 5.115,0.656 5.427,0.854 0.313,0.198 10 false 42 4.458,0.646 4.771,0.844 0.313,0.198 10 false 3 3.854,0.656 4.167,0.854 0.313,0.198 10 false 3 3.031,0.656 3.188,0.854 0.156,0.198 10 false 2 2.438,0.656 2.594,0.854 0.156,0.198 10 false 2 1.729,0.646 1.885,0.844 0.156,0.198 10 false 2 1.74,1.813 1.896,2.01 0.156,0.198 10 false 1 2.396,1.844 2.552,2.042 0.156,0.198 10 false 1 3.021,1.844 3.177,2.042 0.156,0.198 10 false 1 3.802,1.833 4.115,2.031 0.313,0.198 10 false 15 4.448,1.823 4.76,2.021 0.313,0.198 10 false 15 6.49,0.792 6.948,0.99 0.458,0.198 10 false ADC 3.552,1.073 4.01,1.271 0.458,0.198 10 false AN3 3.552,1.25 5.365,1.469 1.813,0.219 10 false No. 2 Floor Wire Connector

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)
a.
C414303

Check the connection condition of the rear motor temperature sensor connector (No. 2 floor wire connector) and the contact pressure of each terminal. Check the terminal for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (FRAME WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (FRAME WIRE CONNECTOR)
a.
C414268

Check the connection condition of the rear motor temperature sensor connector (frame wire connector) and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.READ VALUE USING GTS (REAR MOTOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (REAR MOTOR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.


d.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

5.READ VALUE USING GTS (CHECK WIRE HARNESS OPEN CIRCUIT)

B

9.READ VALUE USING GTS (CHECK WIRE HARNESS SHORT CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (CHECK WIRE HARNESS OPEN CIRCUIT)
a.
C414268E01
0.729,2.01 1.083,2.229 0.354,0.219 0.729,2.021 1.073,2.208 0.344,0.188 10 true ON1

Disconnect the ON1 frame wire connector.


b.
C414306C01
1.583,0.104 1.958,0.344 0.375,0.24 2.229,0.927 2.698,0.802 true 1.99,0.927 2.698,0.448 true 0.156,0.177 0.469,0.333 0.313,0.156 10 false *a 1.635,0.146 1.99,0.344 0.354,0.198 10 false ON1 2.76,0.323 3.167,0.521 0.406,0.198 10 false RMT 2.771,0.708 3.323,0.938 0.552,0.229 10 false RMTG
*a Front view of frame wire connector
(Hybrid Vehicle Control ECU Assembly Side)


Connect terminals 1 (RMTG) and 2 (RMT) of the ON1 frame wire connector (hybrid vehicle control ECU assembly side).


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.


f.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
OK:
Tester Display Condition Specified Condition
Rear Motor Temperature Terminals ON1-1 (RMTG) and ON1-2 (RMT) connected
Power switch on (IG)
215°C (419°F)



g.

Turn the power switch off.


h.

Reconnect the ON1 frame wire connector.


Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR TEMPERATURE SENSOR CONNECTOR)

NG

8.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
6.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR TEMPERATURE SENSOR CONNECTOR)
a.

Remove the rear suspension member sub-assembly.

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER (for HV Model 4WD/AWD)>REMOVAL


b.
C414304

Check the connection condition of the rear motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C


c.

Install the rear suspension member sub-assembly.



A

7.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)
a.

Remove the rear suspension member sub-assembly.

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER (for HV Model 4WD/AWD)>REMOVAL


b.
C414304E01
0.969,1.406 1.24,1.604 0.271,0.198 0.99,1.417 1.229,1.594 0.24,0.177 10 true O2

Disconnect the O2 rear motor temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

OK:
Tester Connection Switch Condition Specified Condition
1 (RMTG) - 2 (RMT) Power switch off 0.3443 to 1446 kΩ



d.
C414305C01
1.615,1.198 1.073,1.656 true 1.875,1.188 2.49,1.708 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 0.844,1.719 1.26,1.948 0.417,0.229 10 false RMT 2.458,1.75 3,2.031 0.542,0.281 10 false RMTG
*a Component without harness connected
(Rear Motor Temperature Sensor (Rear Traction Motor with Transaxle Assembly))


Connect the O2 rear motor temperature sensor connector.


e.

Install the rear suspension member sub-assembly.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR MOTOR TEMPERATURE SENSOR - NO. 2 FLOOR WIRE)

NG

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

8.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
a.

Connect terminals 42 (RMT) and 43 (RMTG) of the A29 hybrid vehicle control ECU assembly connector.

A435159C03
1.479,0.344 1.823,0.594 0.344,0.25 1.813,1.604 2.146,2.365 true 1.688,1.615 1.552,2.344 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.531,0.385 1.99,0.583 0.458,0.198 10 false A29 1.354,2.385 1.844,2.635 0.49,0.25 10 false RMTG 2.073,2.406 2.688,2.604 0.615,0.198 10 false RMT
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
- -



b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.


e.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
OK:
Tester Display Condition Specified Condition
Rear Motor Temperature Terminals A29-42 (RMT) and A29-43 (RMTG) connected
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRAME WIRE - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

9.READ VALUE USING GTS (CHECK WIRE HARNESS SHORT CIRCUIT)
a.
C414268E01
0.729,2.01 1.083,2.229 0.354,0.219 0.729,2.021 1.073,2.208 0.344,0.188 10 true ON1

Disconnect the ON1 frame wire connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Rear Motor Temperature.


e.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Rear Motor Temperature
50003 397 70
OK:
Tester Display Switch Condition Specified Condition
Rear Motor Temperature Power switch on (IG) -40°C



f.

Turn the power switch off.


g.

Reconnect the ON1 frame wire connector.


Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR TEMPERATURE SENSOR CONNECTOR)

NG

12.CHECK HARNESS AND CONNECTOR (FRAME WIRE - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
10.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR TEMPERATURE SENSOR CONNECTOR)
a.

Remove the rear suspension member sub-assembly.

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER (for HV Model 4WD/AWD)>REMOVAL


b.
C414304

Check the connection condition of the rear motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C


c.

Install the rear suspension member sub-assembly.



A

11.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR TEMPERATURE SENSOR)
a.

Remove the rear suspension member sub-assembly.

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER (for HV Model 4WD/AWD)>REMOVAL


b.
C414304E01
0.969,1.406 1.24,1.604 0.271,0.198 0.99,1.417 1.229,1.594 0.24,0.177 10 true O2

Disconnect the O2 rear motor temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

OK:
Tester Display Switch Condition Specified Condition
1 (RMTG) - 2 (RMT) Power switch off 0.3443 to 1446 kΩ



d.
C414305C01
1.615,1.198 1.073,1.656 true 1.875,1.188 2.49,1.708 true 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 0.844,1.719 1.26,1.948 0.417,0.229 10 false RMT 2.458,1.75 3,2.031 0.542,0.281 10 false RMTG
*a Component without harness connected
(Rear Motor Temperature Sensor (Rear Traction Motor with Transaxle Assembly))


Connect the O2 rear motor temperature sensor connector.


e.

Install the rear suspension member sub-assembly.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR MOTOR TEMPERATURE SENSOR - NO. 2 FLOOR WIRE)

NG

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (FRAME WIRE - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the ON1 frame wire connector.


b.

Disconnect the A29 hybrid vehicle control ECU assembly connector.


c.
C414355C01
1.521,0.229 1.917,0.49 0.396,0.26 1.531,2.156 1.917,2.417 0.385,0.26 2.802,0.938 2.219,1.073 true 2.083,1.083 2.823,0.583 true 1.531,4.156 1.708,3.688 true 2.042,4.156 1.875,3.677 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.208,2.219 0.521,2.417 0.313,0.198 10 false *b 1.594,0.281 1.906,0.479 0.313,0.198 10 false ON1 1.594,2.198 1.906,2.396 0.313,0.198 10 false A29 2.854,0.854 3.313,1.083 0.458,0.229 10 false RMTG 2.865,0.49 3.323,0.719 0.458,0.229 10 false RMT 1.375,4.208 1.833,4.438 0.458,0.229 10 false RMT 1.948,4.198 2.406,4.427 0.458,0.229 10 false RMTG
*a Front view of frame wire connector
(Hybrid Vehicle Control ECU Assembly Side)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Display Switch Condition Specified Condition
ON1-1 (RMTG) - A29-43 (RMTG) Power switch off Below 1 Ω
ON1-2 (RMT) - A29-42 (RMT) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Display Switch Condition Specified Condition
ON1-1 (RMTG) or A29-43 (RMTG) - Body ground and other terminals Power switch off 10 kΩ or higher
ON1-2 (RMT) or A29-42 (RMT) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the A29 hybrid vehicle control ECU assembly connector.


e.

Connect the ON1 frame wire connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR