The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.
This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.
If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.
Be sure to wear insulating gloves when working on high voltage wiring or components.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
58398F
1.REMOVE NO. 1 FLOOR UNDER COVER (w/ NO. 1 FLOOR UNDER COVER)
Remove the 3 bolts, 3 clips and No. 1 floor under cover from the rear suspension member sub-assembly.
48812
2.REMOVE REAR STABILIZER BAR
3.REMOVE REAR DRIVE SHAFT ASSEMBLY LH
4.REMOVE REAR DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
5.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
6.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
7.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
Remove the bolt, nut and rear No. 1 suspension arm assembly from the rear suspension member sub-assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48710A
8.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
G3834
9.REMOVE SERVICE PLUG GRIP
82111
10.DISCONNECT ENGINE ROOM MAIN WIRE
11.REMOVE CONNECTOR COVER ASSEMBLY
12.CHECK TERMINAL VOLTAGE
13.INSTALL CONNECTOR COVER ASSEMBLY
82111
14.CONNECT ENGINE ROOM MAIN WIRE
15.REMOVE REAR SEAT ASSEMBLY
73706
16.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
64910N
17.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
58410B
18.REMOVE DECK BOARD ASSEMBLY
58417H
19.REMOVE REAR NO. 3 FLOOR BOARD
64993
20.REMOVE REAR DECK FLOOR BOX (w/o Spare Tire)
58386
21.REMOVE REAR FLOOR FINISH PLATE
58577E
22.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
67918E
23.REMOVE REAR DOOR SCUFF PLATE LH
62332C
24.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
62552F
25.REMOVE REAR SEAT SIDE GARNISH LH
73708A
26.REMOVE TETHER ANCHOR BRACKET SET
58460D
27.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
64740E
28.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
821H1
29.DISCONNECT FLOOR UNDER WIRE
Be sure to wear insulated gloves.
Insulate the disconnected connectors with insulating tape.
Disengage the clamp.
| *a | Waterproof Seal |
Remove the 2 bolts and HV floor under wire from the rear traction motor with transaxle assembly.
Do not damage the terminals, interlock connector or rear traction motor with transaxle assembly during disconnection.
Do not touch the waterproof seal or terminals of the connector.
Do not allow any foreign matter or water to enter the rear traction motor with transaxle assembly.
Although the connector may feel loose, this is not due to a malfunction.
Temporarily install the HV floor under wire as shown in the illustration.
|
Front of the Vehicle | - | - |
51206A
30.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY
Disconnect the 2 connectors.
Remove the grommet of the wire harness and pass the connector through the hole to the outside of the vehicle.
Disengage the 5 clamps to separate the wire harness.
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment and Wooden Block Placement Location |
Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.
Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.
Slowly lower the rear suspension member sub-assembly.
When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.
Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.
31.DISCONNECT WIRE HARNESS
G1050
32.REMOVE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY
48790
33.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
34.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
52272A
35.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
52271E
36.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
Perform the same procedure as for the LH side.
52276B
37.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH
52275C
38.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH
Perform the same procedure as for the LH side.
41651G
39.REMOVE DIFFERENTIAL MOUNT CUSHION
Using SST, remove the differential mount cushion.
| *1 | Rear Suspension Member Sub-assembly | - | - |
| *a | Turn | *b | Hold |
|
Turning Direction |
|
Front of Vehicle |
|
SST Bolt Position | - | - |
Do not bring SST into contact with the rear suspension member sub-assembly.
Before using SST, apply grease to SST bolt.
Set SST in the correct direction.
Do not tilt the bolt of SST.
Do not reuse the differential mount cushion.
40.REMOVE HOLE PLUG
Remove the 6 hole plugs from the rear suspension member sub-assembly.
There are 2 different shapes of hole plug.