Home › Drivetrain › Q610 (HYBRID TRANSMISSION / TRANSAXLE) › REAR TRACTION MOTOR › 2020.05–2020.08
RM3620E _52 Drivetrain _080124 Q610 HYBRID TRANSMISSION / TRANSAXLE _0388721 REAR TRACTION MOTOR A

Q610 HYBRID TRANSMISSION / TRANSAXLE  REAR TRACTION MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear traction motor with transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Rear wheel alignment adjustment
·

Clear zero point calibration data.

·

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for HV model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FXS w/ Canister Pump Module:

(Click here)

·

for A25A-FXS w/o Canister Pump Module:

(Click here)

·

for A25B-FXS:

(Click here)


Rear traction motor with transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY:(Click here)
for 4WD/AWD with LITHIUM-ION BATTERY:(Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

for 4WD/AWD with Nickel Metal Hydride Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 4WD/AWD with Lithium-ion Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 58410B 1.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 2.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 3.REMOVE BATTERY HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441J 5.REMOVE BATTERY SERVICE HOLE COVER

Hide 82111 7.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 82111 11.CONNECT ENGINE ROOM MAIN WIRE

Hide 51206A 14.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

Hide 15.DISCONNECT WIRE HARNESS

a.
C402458C01
1,0.146 1.188,0.146 1.188,0.146 2.188,0.375 true 1.656,1.01 1.938,1.01 1.938,1.01 2.323,0.844 true 0.792,0.052 1.01,0.292 0.219,0.24 10 true *a 1.427,0.917 1.646,1.135 0.219,0.219 10 true *b
*a Temperature Sensor Connector
*b Resolver Sensor Connector


Disconnect the temperature sensor connector.


b.

Disconnect the resolver sensor connector.


c.

Detach the 4 clamps to disconnect the wire harness from the rear traction motor with transaxle assembly and rear suspension member sub-assembly.


Hide G1050 16.REMOVE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

a.

Using an engine sling device and chain block, hold the rear traction motor with transaxle assembly.

CAUTION:
·

Do not lift the rear traction motor with transaxle assembly more than necessary.

·

Check the center of gravity while lifting the rear traction motor with transaxle assembly.



NOTICE:
·

Lightly shake the rear traction motor with transaxle assembly by hand to make sure it is securely held while performing work.

·

Do not shake the rear traction motor with transaxle assembly excessively while holding it.




b.
C402459C01
0.396,2.927 0.521,2.927 0.521,2.927 0.583,3.052 false 0.344,3.875 0.458,3.875 0.458,3.875 0.521,3.948 false 0.219,2.854 0.417,3.063 0.198,0.208 10 false *1 0.177,3.802 0.375,4.031 0.198,0.229 10 false *2
*1 Upper Differential Mount Stopper
*2 Lower Differential Mount Stopper


Remove the 3 bolts, 2 upper differential mount stoppers, 2 lower differential mount stoppers and rear traction motor with transaxle assembly from the rear suspension member sub-assembly.

NOTICE:
·

Do not drop the rear traction motor with transaxle assembly.

·

Do not damage the installation surface of the rear traction motor with transaxle assembly.




Hide 17.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C407248

Remove the 4 bolts and 3 wire harness clamp brackets from the rear traction motor with transaxle assembly.


Hide 52380F 18.REMOVE FRONT DIFFERENTIAL SUPPORT ASSEMBLY

a.
C402460

Remove the 2 bolts and front differential support assembly from the rear traction motor with transaxle assembly.


Hide G1050C 19.REMOVE REAR TRACTION MOTOR FILLER PLUG

HINT:

There is no need to remove this unless the rear traction motor filler plug is replaced.


a.
C415268

Using a 10 mm hexagon socket wrench, remove the rear traction motor filler plug and gasket from the rear traction motor with transaxle assembly.