MALFUNCTION DESCRIPTION
This DTC is stored when the rear motor temperature sensor output is abnormal.
The cause of this DTC output may be the following:
Rear motor temperature sensor internal malfunction
The connectors are not connected properly
Foreign matter or water on the connector terminals
When this DTC is stored, the rear motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the rear motor becomes high. If the self-protection function does not operate, the rear motor may malfunction and cause the vehicle to enter fail-safe mode.
Refer to the wiring diagram for DTC P0A3011.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A302A | Drive Motor "B" Temperature Sensor Signal Stuck In Range | The difference between the maximum and minimum output temperatures of the rear traction motor is less than the stuck malfunction judgment deviation.
(1 trip detection logic) |
Rear traction motor with transaxle assembly(Rear motor temperature sensor) | Does not come on | Master Warning: Comes on |
| DTC No. | Data List |
|---|---|
| P0A302A | Rear Motor Temperature |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Drive the vehicle at approximately 10 km/h (6 mph) or less for approximately 60 seconds or more while maintaining the vehicle speed.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connection condition of the rear motor temperature sensor connector (No. 2 floor wire connector) and the contact pressure of each terminal. Check the terminal for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connectors.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Check the connection condition of the rear motor temperature sensor connector (frame wire connector) and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Remove the rear suspension member sub-assembly.
Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER (for HV Model 4WD/AWD)>REMOVAL
Check the connection condition of the rear motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
Install the rear suspension member sub-assembly.
A
B
C