Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › from 2020.05
RM3620E _52 Drivetrain _076274 P710 HYBRID TRANSMISSION / TRANSAXLE _0371335 HYBRID VEHICLE TRANSAXLE A

P710 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 35162B 1.INSTALL TRANSAXLE CASE PROTECTOR (for 4WD/AWD)

a.

Install the transaxle case protector to the hybrid vehicle transaxle assembly with the clip.


b.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 33185B 2.INSTALL TRANSAXLE UNDER STOPPER BRACKET

a.
C407293C01
2.135,1.552 2.292,1.75 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the transaxle under stopper bracket to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



Hide 3.INSTALL STUD BOLT

a.

Clean and degrease the bolt holes of the hybrid vehicle transaxle assembly.


b.

Apply adhesive to 2 or 3 threads on the ends of the 2 stud bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the 2 stud bolts, apply adhesive to the 2 stud bolts and install them within 10 minutes of adhesive application.



c.

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the hybrid vehicle transaxle assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 4.INSTALL TRANSAXLE HOUSING PLUG

a.

Install the transaxle housing plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 5.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 4 bolts.

C405644C01
0.906,0.51 1.063,0.708 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B


Torque:
for bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
for bolt B : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 82125 6.INSTALL TRANSMISSION WIRE

a.

Install the transmission wire to the hybrid vehicle transaxle assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the connector.


Hide 44781E 7.INSTALL HOSE BRACKET

a.
C379403N01
1.031,1.677 1.188,1.875 0.156,0.198 10 true 1 1.417,1.729 1.573,1.927 0.156,0.198 10 true 2

Temporarily install the hose bracket to the hybrid vehicle transaxle assembly with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 33823 8.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide G125A 9.INSTALL MOTOR COOLING COOLER

Hide 30900 11.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C379784C02
2.313,0.219 2.469,0.427 0.156,0.208 10 false -
V100135

Knock Pin


Make sure that the knock pins are installed to the engine assembly.


b.
C379785C01
2.542,0.479 2.698,0.677 0.156,0.198 10 false -
V100135

Bolt A


Align the knock pins with the holes in the hybrid transaxle assembly and, while keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, temporarily install the bolt (A).

NOTICE:
·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly are in close contact with one another.

·

Do not apply grease to the inner splines of the transmission input damper assembly or input shaft assembly.

·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excessive force when installing the hybrid vehicle transaxle assembly.

·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft assembly of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.

·

When inserting the input shaft assembly of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the hybrid vehicle transaxle assembly excessively.

·

When installing the hybrid vehicle transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock pin holes.




c.
C405645C01
2.438,0.531 2.594,0.729 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D


While keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, install the 8 bolts.

Torque:
for bolt A and bolt B : 64 N*m (653 kgf*cm, 47 ft.*lbf)
for bolt C : 46 N*m (469 kgf*cm, 34 ft.*lbf)
for bolt D : 25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:
Bolt Bolt Length
A and B 50 mm (1.97 in.)
C 45 mm (1.77 in.)
D 35 mm (1.38 in.)



Hide 12303 12.INSTALL REAR ENGINE MOUNTING BRACKET

a.
C405646C01
1.531,0.667 1.729,0.875 0.198,0.208 10 false -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the rear engine mounting bracket to the hybrid vehicle transaxle assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (A) → Tighten bolt (C)



Hide 13.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the rear engine mounting insulator with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12371A 14.INSTALL REAR ENGINE MOUNTING INSULATOR

Hide 12311A 15.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C405647C01
1.365,0.531 1.521,0.729 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the transverse engine engine mounting bracket to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



Hide 12361 16.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the transverse engine engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 11363A 18.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the engine assembly.


Hide 28193 19.INSTALL STARTER HOLE INSULATOR

a.

Install the starter hole insulator to the engine assembly with the 2 bolts.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 821H2 20.CONNECT HV AIR CONDITIONING WIRE

a.

for 2WD:

i.

Attach the guide to connect the HV air conditioning wire to the hybrid vehicle transaxle assembly.


ii.

Install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



b.

for 4WD/AWD:

i.

Attach the guide to connect the HV air conditioning wire to the hybrid vehicle transaxle assembly.


ii.

Install the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



Hide 82121 21.CONNECT ENGINE WIRE (for LHD)

a.

Connect the 5 clamps.

C393903C01
0.729,1.938 0.885,2.083 0.156,0.146 10 false -
V100135

Bolt A
V100136

Bolt B



b.

Install the 2 bolts.

Torque:
for bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
for bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82121 22.CONNECT ENGINE WIRE (for RHD)

a.

Connect the 4 clamps.

C405643C01
0.74,1.938 0.896,2.135 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B



b.

Install the 2 bolts.

Torque:
for bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
for bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23.CONNECT WIRE HARNESS (for RHD)

Hide 24.CONNECT WIRE HARNESS (for LHD)

Hide 45319 25.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 28.INSTALL ENGINE ASSEMBLY WITH HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 29. PERFORM RESOLVER LEARNING