Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › INPUT SHAFT OIL SEAL › 2020.05–2020.08
RM3620E _52 Drivetrain _076274 P710 HYBRID TRANSMISSION / TRANSAXLE _0371341 INPUT SHAFT OIL SEAL A

P710 HYBRID TRANSMISSION / TRANSAXLE  INPUT SHAFT OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during input shaft type T oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM
for A25A-FXS(w/ Canister Pump Module):

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
for A25A-FXS(w/o Canister Pump Module):

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
for A25A-FXS:

Grille shutter switch specification infomation


Vehicle control history (RoB) [X260E] is stored w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)
for A25B-FXS:

Perform Vehicle Identification Number (VIN) or frame number registration


DTC P063051 is output (Click here)
for A25A-FXS:
·

Engine assembly

·

Air fuel ratio sensor (sensor 1)

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
for A25A-FXS(w/o Canister Pump Module):

Front exhaust pipe assembly*2


GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
for A25B-FXS:
·

Engine assembly

·

Air fuel ratio sensor (sensor 1)

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD with NICKEL METAL HYDRIDE BATTERY:(Click here)
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY:(Click here)
for 2WD with LITHIUM-ION BATTERY:(Click here)
for 4WD/AWD with LITHIUM-ION BATTERY:(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for HV model) (Click here)
Replacement of the headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Front wheel alignment adjustment
·

Clear zero point calibration data.

·

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD with Nickel Metal Hydride Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 4WD/AWD with Nickel Metal Hydride Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 2WD with Lithium-ion Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>PRECAUTION

for 4WD/AWD with Lithium-ion Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

If the ECM has been struck or dropped, replace it.

·

for A25A-FXS:

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION

·

for A25B-FXS:

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 35710A 2.REMOVE INPUT SHAFT TYPE T OIL SEAL

a.
C377405C02
1.188,0.344 1.479,0.344 1.479,0.344 1.844,1 true 1.021,0.25 1.302,0.458 0.281,0.208 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the input shaft type T oil seal from the hybrid vehicle transaxle assembly.

NOTICE:

Be careful not to damage the input shaft assembly or hybrid vehicle transaxle assembly.



Hide 35710A 3.INSTALL INPUT SHAFT TYPE T OIL SEAL

a.

Coat the lip of a new input shaft type T oil seal with a small amount of MP grease.


b.
C377942C01
1.99,1.969 2.365,3.021 2.365,3.021 2.521,3.021 true 1.385,0.115 1.667,0.333 0.281,0.219 10 false *a 2.563,2.927 3.021,3.125 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install the input shaft type T oil seal to the hybrid vehicle transaxle assembly.

SST
09608-04031  

Standard Depth:

1.9 to 2.7 mm (0.0748 to 0.106 in.)


NOTICE:
·

Do not allow foreign matter to attach to the lip of the input shaft type T oil seal.

·

Do not install the input shaft type T oil seal at an angle.




Hide 30900 4.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY