If a malfunction is detected in the power supply circuit, the skid control ECU (brake booster with master cylinder assembly) power source voltage drops, or there is insufficient voltage to operate the ABS main relay, the skid control ECU (brake booster with master cylinder assembly) will store these DTCs.
These DTCs may also be stored if the auxiliary battery voltage drops below 9.5 V.
DTC C1256 (Accumulator Low Pressure) may also be memorized if there is a drop in power source voltage.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1241 | Low or High Power Supply Voltage | 101
102 551 552 553 |
·
INF Code: 101 -
Any of the following is detected when the BS terminal voltage is 9.3 V or less: (1)
Vehicle not decelerated (brake pedal is not depressed) for 3 seconds or more. (2)
While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A. (3)
Vehicle decelerated (brake pedal is depressed) for 0.06 seconds. ·
INF Code: 102 -
Any of the following is detected when the ECU internal voltage is 6.8 V or less: (1)
With the power switch off, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command. (2)
With the power switch off and the IG1 terminal voltage 9.5 V or less, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command. (3)
Sensor supply voltage is 4.75 V or less, or 5.25 V or more for 0.06 seconds. (4)
Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more for 0.06 seconds. ·
INF Code: 551 -
When driving at 3 km/h (1.9 mph) or more, IG1 terminal voltage is 9.5 V or less, or VM1 voltage is 8.6 V or less for 10 seconds or more. ·
INF Code: 552 -
When VM1 voltage is 8.6 V or less, sensor supply voltage is low for 60 seconds or more. ·
INF Code: 553 -
VM1 voltage is 16.6 V or more for 0.8 seconds. |
·
Improperly connected connector, deformation or corrosion of terminals ·
Auxiliary battery ·
Hybrid control system (Charging circuit) ·
Skid control ECU (Brake booster with master cylinder assembly) |
- |
| C1242 | Open Circuit in IG1/IG2 Power Source Circuit | 111
112 |
·
INF Code: 111 -
Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V higher than) for 4 seconds or more. ·
INF Code: 112 -
While hybrid vehicle control ECU assembly communication is enabled, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously for 4 seconds or more. -
When the vehicle speed exceeds 10 km/h, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously for 4 seconds or more. |
·
INF Code: 111 -
Open or short in IG1 circuit -
Improperly connected connector, deformation or corrosion of terminals -
Entry and start system (for start function, HV Model) -
Auxiliary battery -
Hybrid control system (Charging circuit) -
Skid control ECU (Brake booster with master cylinder assembly) ·
INF Code: 112 -
Open or short in IG2 circuit -
Improperly connected connector, deformation or corrosion of terminals -
Entry and start system (for start function, HV Model) -
Auxiliary battery -
Hybrid control system (Charging circuit) -
Skid control ECU (Brake booster with master cylinder assembly) |
- |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | BS terminal voltage is 9.3 V or less | ○ | ○ | ○ |
| Malfunction Status | Vehicle not decelerated (brake pedal is not depressed) | ○ | - | - |
| While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A | - | ○ | - | |
| Vehicle decelerated (brake pedal is depressed) | - | - | ○ | |
| Detection Time | 3 seconds or more | - | 0.06 seconds | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | ||
| Diagnosis Condition | ECU internal voltage is 6.8 V or less | ○ | ○ | ○ | ○ |
| Malfunction Status | With the power switch off, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command | ○ | - | - | - |
| With the power switch off and the IG1 terminal voltage 9.5 V or less, the main relay contact voltage does not reach 3.5 V or more continuously for 0.22 seconds or more in response to a main relay ON command | - | ○ | - | - | |
| Sensor supply voltage is 4.75 V or less, or 5.25 V or more | - | - | ○ | - | |
| Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more | - | - | - | ○ | |
| Detection Time | - | - | 0.06 seconds | 0.06 seconds | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | - | - | - |
| Malfunction Status | While hybrid vehicle control ECU assembly communication is enabled, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously | ○ | - |
| When the vehicle speed exceeds 10 km/h, no voltage (below 3.5 V) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously | - | ○ | |
| Detection Time | 4 seconds or more | 4 seconds or more | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check if entry and start system (for start function, HV Model) DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Check if hybrid control system DTCs are output.
for 2WD with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>DTC CHECK / CLEAR
for 2WD with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>DTC CHECK / CLEAR
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>DTC CHECK / CLEAR
for 4WD/AWD with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
for 2WD with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
for 2WD with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
for 4WD/AWD with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
Check that no main relay malfunction DTCs are output.
| Result | Proceed to |
|---|---|
| Main relay malfunction DTCs are not output. | A |
| Main relay malfunction DTCs are output. | B |
A
B
Check the auxiliary battery voltage.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Auxiliary battery | Power switch on (IG) | 11 to 14 V |
| Auxiliary battery | Power switch on (READY) | 11 to 15.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-14 (BI) - Body ground | Always | 11 to 14 V |
| A42-15 (BS) - Body ground | Always | 11 to 14 V |
| A42-16 (IG1) - Body ground | Power switch on (IG) | 11 to 14 V |
| A42-12 (IG2) - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-28 (GND) - Body ground | Always | Below 1 Ω |
| A42-27 (GND2) - Body ground | Always | Below 1 Ω |
| A42-26 (GND3) - Body ground | Always | Below 1 Ω |
| A42-25 (GND4) - Body ground | Always | Below 1 Ω |
| A42-24 (GND5) - Body ground | Always | Below 1 Ω |
| A42-23 (GND6) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (READY).
Perform a road test.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C1241 and C1242 are not output. | A |
| DTCs C1241 and/or C1242 are output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD without Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD without Vacuum Brake Booster)>REMOVAL