Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster) › from 2020.05
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1345  Linear Solenoid Valve Offset Learning undone  C1368  Linear Solenoid Valve Offset  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores and corrects the individual differences in the brake pedal stroke sensor assembly, actuator solenoids, and stroke simulator solenoid. Perform initialization and calibration of the linear solenoid valve if any of these parts is replaced.

The skid control ECU (brake booster with master cylinder assembly) receives the shift position P signal from the hybrid vehicle control ECU assembly through the CAN communication system.

These DTCs are cleared when the linear valve offset learning results are normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1345 Linear Solenoid Valve Offset Learning undone - Linear valve offset learning undone. Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. -
C1368 Linear Solenoid Valve Offset - Offset learned value out of specification.
·

Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Brake actuator (Brake booster with master cylinder assembly)


-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


HINT:

When C1451 is output together with C1345 and/or C1368, inspect and repair the trouble areas indicated by C1451 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>C1451


PROCEDURE

1.CHECK DTC

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check the DTCs (electronically controlled brake system and hybrid control system) that are output.

for Electronically Controlled Brake System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

for Hybrid Control System (for 2WD with NICKEL METAL HYDRIDE BATTERY): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>DTC CHECK / CLEAR

for Hybrid Control System (for 2WD with LITHIUM-ION BATTERY):Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>DTC CHECK / CLEAR

for Hybrid Control System (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>DTC CHECK / CLEAR

for Hybrid Control System (for 4WD/AWD with LITHIUM-ION BATTERY): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs (except C1345, C1368 and hybrid control system DTCs) are not output. A
Hybrid control system DTCs are output. B
DTCs (except C1345 and/or C1368) are output. C


HINT:

Before performing initialization and calibration of the linear solenoid valve, C1203 will be output.




A

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE

B

C

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
a.

Turn the power switch off.


b.

Perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 1167

Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Turn the power switch off.



c.

Turn the power switch off.


d.

Turn the power switch on (IG).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1345 and C1368 are not output. A
DTCs C1345 and/or C1368 are output. B



A

END

B