The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
43457
1.REMOVE DRIVE SHAFT BEARING BRACKET
| *A | for 2WD |
| *B | for 4WD/AWD |
Remove the 3 bolts and drive shaft bearing bracket.
16361A
2.REMOVE V-RIBBED BELT
27020
3.REMOVE GENERATOR ASSEMBLY
for 100 A, 130 A Type:
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 100 A, 130 A Type)>REMOVAL
for 150 A Type:
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 150 A Type)>REMOVAL
88310
4.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY
for Type A:
|
Bolt |
|
Nut |
Remove the 2 bolts and 2 nuts.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor assembly with pulley.
for Type B:
Remove the 4 bolts and compressor assembly with pulley.
12602C
5.REMOVE NO. 2 ENGINE COVER
Remove the 2 bolts and No. 2 engine cover from the No. 2 timing chain cover assembly.
16620D
6.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.
Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.
Remove the 2 bolts and V-ribbed belt tensioner assembly from the No. 2 timing chain cover assembly.
11336A
7.REMOVE NO. 2 TIMING CHAIN COVER INSULATOR
Remove the No. 2 timing chain cover insulator from the V-ribbed belt tensioner assembly.
11336A
8.REMOVE TIMING GEAR COVER INSULATOR
Using an 8 mm socket wrench, remove the bolt, plate washer and timing gear cover insulator from the No. 2 timing chain cover assembly.
11323C
9.REMOVE NO. 3 TIMING CHAIN COVER
Using an 8 mm socket wrench, remove the bolt, plate washer and No. 3 timing chain cover from the No. 2 timing chain cover assembly.
16207
10.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the outlet water by-pass sub-assembly.
Remove the bolt and No. 2 water by-pass pipe sub-assembly.
16260
11.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
Remove the bolt to disconnect the flow shutting valve (water by-pass hose assembly).
Remove the 2 bolts and the water hose clamp bracket.
Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the water by-pass outlet sub-assembly.
Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and water by-pass outlet sub-assembly.
17167
12.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Remove the 5 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.
17118
13.REMOVE MANIFOLD STAY
17141
14.REMOVE EXHAUST MANIFOLD
Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold from the cylinder head sub-assembly.
Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.
22030
15.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
25680
16.REMOVE EGR COOLER ASSEMBLY
| *1 | No. 3 Water By-pass Hose |
| *2 | Water Hose |
Slide the clip and disconnect the water hose from the EGR cooler assembly.
Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.
Remove the 5 bolts, EGR cooler assembly, EGR cooler gasket and EGR valve gasket.
25687
17.REMOVE NO. 1 EGR COOLER BRACKET
Remove the 2 bolts and No. 1 EGR cooler bracket from the EGR valve bracket and water outlet.
25601
18.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
Using an 8 mm socket wrench, remove the 4 bolts, No. 1 EGR pipe sub-assembly, EGR inlet gasket and EGR valve adapter gasket.
19.REMOVE NO. 4 WATER BY-PASS HOSE
Slide the clip and remove the No. 4 water by-pass hose from the EGR valve assembly.
25620
20.REMOVE EGR VALVE ASSEMBLY
Disconnect the clamp.
Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.
Using an 8 mm socket wrench, remove the bolt and disconnect the fuel pipe sub-assembly from the EGR valve bracket.
Using an 8 mm socket wrench, remove the bolt.
| *a | Pin |
| *b | Hole |
Remove the EGR valve assembly vertically.
Using an 8 mm socket wrench, remove the bolt and EGR valve bracket.
16279
21.REMOVE NO. 3 WATER BY-PASS PIPE
Using an 8 mm socket wrench, remove the bolt and No. 3 water by-pass pipe from the intake manifold.
Slide the clip and disconnect the No. 3 water by-pass pipe from the water outlet.
16278
22.REMOVE NO. 2 WATER BY-PASS PIPE
Remove the bolt (A).
Using an 8 mm socket wrench, remove the 2 bolts (B) and No. 2 water by-pass pipe.
17111
23.REMOVE INTAKE MANIFOLD
17177
24.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET
23901
25.DISCONNECT FUEL TUBE SUB-ASSEMBLY
23801P
26.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
23100X
27.REMOVE FUEL PUMP ASSEMBLY (for High Pressure)
16295
28.REMOVE NO. 7 WATER BY-PASS HOSE
Slide the 2 clips and remove the No. 7 water by-pass hose.
82219A
29.REMOVE SENSOR WIRE
Disconnect the 4 connectors.
Detach the 3 clamps.
Using an 8 mm socket wrench, remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.
82126A
30.REMOVE NO. 6 ENGINE WIRE
Disconnect the 4 connectors.
Detach the 2 clamps.
Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.
31.REMOVE WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.
23807
32.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
23807V
33.REMOVE NO. 1 DELIVERY PIPE SPACER
23291
34.REMOVE INJECTOR VIBRATION INSULATOR
82125N
35.REMOVE NO. 5 ENGINE WIRE
23250F
36.REMOVE PORT FUEL INJECTOR ASSEMBLY
23814B
37.REMOVE FUEL DELIVERY PIPE
23250E
38.REMOVE DIRECT FUEL INJECTOR ASSEMBLY
23255A
39.REMOVE FUEL INJECTOR SEAL
19500
40.REMOVE IGNITION COIL ASSEMBLY
11452
41.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the engine oil level dipstick.
Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly.
Remove the O-ring from the engine oil level dipstick guide.
17169A
42.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Remove the bolt and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.
43.REMOVE PURGE VALVE (PURGE VSV)
w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (EMISSION CONTROL)>PURGE VALVE(w/ Canister Pump Module)>REMOVAL
w/o Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (EMISSION CONTROL)>PURGE VALVE(w/o Canister Pump Module)>REMOVAL
25861A
44.REMOVE NO. 2 VACUUM SWITCHING VALVE BRACKET
Using an 8 mm socket wrench, remove the 2 bolts and No. 2 vacuum switching valve bracket from the cylinder head sub-assembly.