Home › Vehicle Interior › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat) › from 2020.08
RM3620E _58 Vehicle Interior _076406 SEAT BELT _0377519 FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat) A

SEAT BELT  FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Front passenger seat Zero point calibration (Occupant classification system)
·

Occupant classification system (for HV model)

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Front passenger seat Zero point calibration (Occupant Classification System)
·

Occupant classification system (for Gasoline model)

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


CAUTION:
·
B521791

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·
B458500

Be sure to read precaution thoroughly before servicing.


·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 73240 3.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

a.

w/o Occupant Classification System:

i.

Detach the clamp and claw.

B529773



b.

w/ Occupant Classification System:

i.

Detach the clamp and claw.

B521414


ii.

Disconnect the connector.



c.
B521415

Remove the nut and front seat inner belt assembly LH.


d.

Remove the front seat belt anchor plate.


Hide 73230 4.REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

a.

w/o Occupant Classification System:

i.
B521494

Detach the band.


ii.

Disconnect the connector.

B521495


iii.

Detach the clamp and claw.



b.

w/ Occupant Classification System:

i.

Disconnect the connector.

B521418


ii.

Detach the clamp.



c.
B521419

Remove the nut and front seat inner belt assembly RH.


d.

Remove the front seat belt anchor plate.