Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING (for Moon Roof) › from 2020.08
RM3620E _59 Vehicle Exterior _076526 SLIDING ROOF / CONVERTIBLE _0372468 SLIDING ROOF HOUSING(for Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Moon Roof)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof housing removal/installation are shown below.

Necessary Procedure after parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Sliding roof ECU (sliding roof drive gear sub-assembly) Initialize sliding roof system
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter-linked function

·

Sliding roof open warning function

·

Sliding roof may move in reverse or become misaligned


(Click here)
Sliding roof drive cable sub-assembly (Including removal and installation) Initialize sliding roof system
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter-linked function

·

Sliding roof open warning function

·

Sliding roof may move in reverse or become misaligned


Sliding roof glass sub-assembly (Including removal and installation) Initialize sliding roof system
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter-linked function

·

Sliding roof open warning function

·

Sliding roof may move in reverse or become misaligned



NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Sliding roof ECU (sliding roof drive gear sub-assembly) Initialize sliding roof system
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter-linked function

·

Sliding roof open warning function

·

Sliding roof may move in reverse or become misaligned


(Click here)
Sliding roof drive cable sub-assembly (Including removal and installation) Initialize sliding roof system
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter-linked function

·

Sliding roof open warning function

·

Sliding roof may move in reverse or become misaligned


Sliding roof glass sub-assembly (Including removal and installation) Initialize panoramic moon roof system (for sliding roof)
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter-linked function

·

Sliding roof open warning function

·

Sliding roof may move in reverse or become misaligned



NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 63218S 2.REMOVE SLIDING ROOF SIDE GARNISH LH

a.

Move the sliding roof glass sub-assembly to the fully tilted up position.


b.
B564395

Detach the claw and remove the sliding roof side garnish LH.


Hide 63217R 3.REMOVE SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 63201P 4.REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY

NOTICE:
·

Carrying the sliding roof glass sub-assembly from the vehicle must be performed by multiple people.

·

Be careful not to damage the sliding roof glass sub-assembly, body exterior or interior parts.

·

To prevent the sliding roof glass sub-assembly from becoming misaligned, move the sliding roof glass sub-assembly to the fully closed position before removing.



a.
B527449

Move the sliding roof glass sub-assembly to the fully closed position.


b.

Using a T25 "TORX" socket wrench, remove the 4 "TORX" screws and sliding roof glass sub-assembly.

HINT:

Use the same procedure for the RH side and LH side.



Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL



c.

for M20A-FKS:

Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 62180A 6.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 7.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 8.DISCONNECT SLIDING ROOF DRAIN HOSE

a.

Detach the sliding roof drain hose clamp and disconnect the 4 sliding roof drain hoses.

B527492


Hide 63203F 9.REMOVE SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

Remove the 4 bolts, 6 nuts and sliding roof housing sub-assembly.

B527493

NOTICE:
B474971

If the removed nut is the same shape as that shown in the illustration, replace it the supplied replacement part.