The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
Use the same procedure described for the LH side.
When performing removal for the rear door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25A-FKS:
for M20A-FKS:
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
69278C
6.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
74646A
7.REMOVE DOOR ASSIST GRIP COVER LH
8.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
67604
9.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
68174A
10.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
68199
11.REMOVE REAR DOOR REAR BELT SEAL LH
67842E
12.REMOVE REAR DOOR SERVICE HOLE COVER LH
67674A
13.REMOVE REAR DOOR FRAME GARNISH LH
68152C
14.DISCONNECT REAR DOOR GLASS RUN LH
67408E
15.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
68124C
16.REMOVE REAR DOOR QUARTER WINDOW GLASS LH
68104
17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
75722A
18.REMOVE REAR DOOR BELT MOULDING LH
|
Protective Tape |
Apply protective tape around the rear door belt moulding LH.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
While pressing the rear door belt moulding LH, pull the edge and detach the claw as shown in the illustration.
|
Remove in this Direction |
Detach the claw to remove the rear door belt moulding LH.