Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Front Door) › from 2020.08
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0376601 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Front door glass sub-assembly LH

·

Front door glass sub-assembly RH

·

Front door glass run LH

·

Front door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.

·

When performing removal for the black out tape, disconnect the negative (-) auxiliary battery terminal after fully opening the front door glass.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 4.REMOVE BATTERY HOLE COVER

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69278B 6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

Hide 74642A 7.REMOVE FRONT DOOR ASSIST GRIP COVER LH

Hide 8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 9.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 67602 10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68172A 11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

Hide 68193C 12.REMOVE FRONT DOOR FRONT BELT SEAL LH

Hide 67832 13.REMOVE FRONT DOOR SERVICE HOLE COVER LH

Hide 68102 14.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 67664C 15.REMOVE DOOR FRAME GARNISH LH

Hide 68151D 16.REMOVE FRONT DOOR GLASS RUN LH

Hide 67402F 17.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH

Hide 68126 18.REMOVE FRONT DOOR FIX WINDOW GLASS LH

Hide 75712B 19.REMOVE FRONT DOOR BELT MOULDING LH

Hide 67862 20.REMOVE FRONT DOOR WEATHERSTRIP LH

Hide 75966B 21.REMOVE FRONT DOOR NO. 4 STRIPE LH

HINT:

When removing the front door No. 4 stripe LH, if it is difficult to remove, heat the adhesive of the front door No. 4 stripe LH and front door panel using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)
Front Door No. 4 Stripe LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front door panel and front door No. 4 stripe LH excessively.


a.
B524066

Pull back on one of the ends of the front door No. 4 stripe LH to remove it.

HINT:

When pulling on the front door No. 4 stripe LH, pull it parallel to the front door panel.



Hide 75986G 22.REMOVE FRONT DOOR OUTSIDE STRIPE LH

HINT:

When removing the front door outside stripe LH, if it is difficult to remove, heat the adhesive of the front door outside stripe LH and front door panel using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)
Front Door Outside Stripe LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front door panel and front door outside stripe LH excessively.


a.
B524067

Pull back on one of the ends of the front door outside stripe LH to remove it.

HINT:

When pulling on the front door outside stripe LH, pull it parallel to the front door panel.



Hide 75922M 23.REMOVE NO. 1 BLACK OUT TAPE LH

HINT:

When removing the No. 1 black out tape LH, if it is difficult to remove, heat the adhesive of the No. 1 black out tape LH and front door panel using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)
No. 1 Black Out Tape LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front door panel and No. 1 black out tape LH excessively.


a.
B524068

Pull back on one of the ends of the No. 1 black out tape LH to remove it.

HINT:

When pulling on the No. 1 black out tape LH, pull it parallel to the front door panel.