The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door disassembly/reassembly are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for RHD and LHD vehicles.
The procedure below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure below is for the LH side.
Before performing disassembly work on the front door, make sure that the front door glass is fully open and be sure to disconnect the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25A-FKS:
for M20A-FKS:
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
69278B
6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
Detach the claw and remove the front door inside handle bezel LH.
74642A
7.REMOVE FRONT DOOR ASSIST GRIP COVER LH
|
Protective Tape |
Apply protective tape to the front door trim board sub-assembly LH as shown in the illustration.
|
Remove in this Direction |
Using a moulding remover A, detach the clip.
Detach the claw in the order shown in the illustration.
|
Remove in this Direction |
Detach the guide in the direction indicated by the arrow shown in the illustration and remove the front door assist grip cover LH.
8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
|
Protective Tape |
Apply protective tape around the multiplex network master switch assembly with front door armrest base panel.
|
Remove in this Direction |
Using a moulding remover A, detach the guide and claw as shown in the illustration.
|
Remove in this Direction |
Detach the guide in the direction indicated by the arrow shown in the illustration and remove the multiplex network master switch assembly with front door armrest base panel.
Disconnect the 2 connectors.
84040
9.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)
84870A
10.REMOVE OUTER MIRROR SWITCH ASSEMBLY (for Driver Side)
11.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
|
Protective Tape |
Apply protective tape around the power window regulator switch assembly with front door armrest base panel.
|
Remove in this Direction |
Using a moulding remover A, detach the guide and claw as shown in the illustration.
|
Remove in this Direction |
Detach the guide in the direction indicated by the arrow shown in the illustration and remove the power window regulator switch assembly with front door armrest base panel.
w/ Door Control Switch:
Disconnect the 2 connectors.
w/o Door Control Switch:
Disconnect the connector.
84810
12.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
84930
13.REMOVE DOOR CONTROL SWITCH ASSEMBLY (w/ Door Control Switch)
67602
14.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
|
Protective Tape |
Apply protective tape to the front door panel as shown in the illustration.
Remove the 3 screws.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration, and while pulling the front door trim board sub-assembly LH toward you, detach the clip and disconnect the front door trim board sub-assembly LH from the front door panel.
Detach the clip in the order shown in the illustration.
Securely detach the clips one by one.
|
Remove in this Direction |
Pull the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration to detach the claw and clip to remove the front door trim board sub-assembly LH.
Detach the claw and clips in the order shown in the illustration.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
|
Remove in this Direction |
Detach the clamp and disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH as shown in the illustration.
w/ Seat Memory Switch:
Disconnect the connector.
84927
15.REMOVE SEAT MEMORY SWITCH (w/ Seat Memory Switch)
69206B
16.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Detach the clamp and claw.
|
Remove in this Direction |
Remove the front door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.
68172A
17.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
|
Remove in this Direction |
|
Protective Tape |
Using a clip remover with its tip wrapped with protective tape, detach the clip.
Detach the guide and roll up the front door weatherstrip LH enough that the front door inner glass weatherstrip LH can be removed.
|
Remove in this Direction |
Remove the front door inner glass weatherstrip LH with front door rear belt seal LH as shown in the illustration.
68195B
18.REMOVE FRONT DOOR REAR BELT SEAL LH
|
Remove in this Direction |
Remove the front door rear belt seal LH from the front door inner glass weatherstrip LH as shown in the illustration.
68193C
19.REMOVE FRONT DOOR FRONT BELT SEAL LH
|
Remove in this Direction |
|
Protective Tape |
Using a clip remover with its tip wrapped with protective tape, detach the clip.
Detach the guide and roll up the front door weatherstrip LH enough that the front door front belt seal LH can be removed.
|
Remove in this Direction |
Remove the front door front belt seal LH as shown in the illustration.
87964
20.REMOVE OUTER MIRROR INSTALL HOLE COVER LH
87940
21.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
86160
22.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
67832
23.REMOVE FRONT DOOR SERVICE HOLE COVER LH
Disconnect the connector.
Detach the clamp.
| *a | Location Mark |
| *b | Bead Mark |
|
Turn in this Direction |
|
Service Hole Cover Clip |
Check that the service hole cover clip knob and bead mark are aligned.
Turn the service hole cover clip 45° clockwise to the location mark and then remove the service hole cover clip.
Use the same procedure for the other service hole cover clips.
|
Protective Tape |
Using a clip remover with its tip wrapped with protective tape, detach the clip.
|
Remove in this Direction |
Pull out the front door lock remote control cable assembly LH and front door inside locking cable assembly LH from the front door service hole cover LH.
8983AA
24.REMOVE SIDE AIRBAG PRESSURE SENSOR LH
68102
25.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Remove the hole plug.
for Driver Side:
Connect the multiplex network master switch assembly connector.
for Front Passenger Side:
Connect the power window regulator switch assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal.
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25A-FKS:
for M20A-FKS:
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>INSTALLATION
Turn the ignition switch to ON.
Move the front door glass sub-assembly LH until the installation bolts can be seen.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25A-FKS:
for M20A-FKS:
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
After disconnecting the cable from the negative (-) auxiliary battery terminal, wait for at least 90 seconds to start the operation.
If the airbag deploys for any reason, it may cause a serious accident.
for Driver Side:
Disconnect the multiplex network master switch assembly connector.
for Front Passenger Side:
Disconnect the power window regulator switch assembly connector.
|
Protective Tape |
Apply protective tape around the front door panel as shown in the illustration.
Remove the 2 bolts.
After the bolts are removed, do not allow the front door glass sub-assembly LH to fall.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door glass sub-assembly LH in the direction indicated by the arrows, in the order shown in the illustration.
Be careful not to damage the front door glass sub-assembly LH.
67664C
26.REMOVE DOOR FRAME GARNISH LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the guide and remove the door frame garnish LH in the direction indicated by the arrows, in the order shown in the illustration.
68151D
27.REMOVE FRONT DOOR GLASS RUN LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door glass run LH as shown in the illustration.
69802
28.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
|
Nut |
|
Connector |
Disconnect the connector.
Remove the 7 nuts and the front door window regulator sub-assembly LH.
Do not damage the front door panel with the front door window regulator sub-assembly LH.
|
Remove in this Direction |
When removing the front door window regulator assembly LH, pull it out from the service hole as shown in the illustration.
85720C
29.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
67404F
30.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Remove the bolt.
Detach the guide and remove the front door rear lower frame sub-assembly LH.
67402F
31.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH
|
Lift up in this Direction |
Lift up the front door weatherstrip LH and remove the screw as shown in the illustration.
Remove the screw.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the 3 bolts.
Remove the front door front lower frame sub-assembly LH in the direction indicated by the arrows, in the order shown in the illustration.
68126
32.REMOVE FRONT DOOR FIX WINDOW GLASS LH
|
Remove in this Direction |
Remove the front door fix window glass LH as shown in the illustration.
75712B
33.REMOVE FRONT DOOR BELT MOULDING LH
69220
34.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
|
Remove in this Direction |
|
Protective Tape |
w/ Entry and Start System:
Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the connector cover as shown in the illustration.
|
Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, detach the claw to disconnect the connector and connector cover as shown in the illustration.
| *1 | Holder |
|
Remove in this Direction |
Detach the holder as shown in the illustration.
|
Remove in this Direction |
Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.
35.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the "TORX" screw.
|
Remove in this Direction |
Remove the front door lock cylinder assembly LH as shown in the illustration.
69217E
36.REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the "TORX" screw.
|
Remove in this Direction |
Detach the claw and remove the front door outside handle cover RH as shown in the illustration.
69241H
37.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
Detach the claw and guide to remove the front door front outside handle pad.
69242F
38.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
Detach the guide and remove the front door rear outside handle pad.
69312
39.REMOVE FRONT DOOR LOCK OPEN ROD LH
| *1 | Snap |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Detach the snap as shown in the illustration.
Remove the front door lock open rod LH in the direction indicated by the arrow shown in the illustration.
69202A
40.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
| *a | Inside |
| *b | Outside |
Using a T30 "TORX" socket wrench, loosen the "TORX"screw.
Detach the guide and remove the front door outside handle frame sub-assembly LH.
w/ Entry and Start System:
Detach the wire harness clamp.
69040A
41.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)
69318C
42.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)
When reusing front door lock with motor assembly LH:
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
69036A
43.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)
69720D
44.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
69760B
45.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
69040A
46.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)
69318C
47.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)
When reusing front door lock with motor assembly LH:
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
69720D
48.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
69760B
49.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
68620
50.REMOVE FRONT DOOR CHECK ASSEMBLY LH
|
Bolt (A) |
|
Bolt (B) |
Remove the 2 bolts (A), bolt (B) and front door check assembly LH.
67862
51.REMOVE FRONT DOOR WEATHERSTRIP LH
|
Protective Tape |
Using a clip remover with its tip wrapped with protective tape, detach the clip.
|
Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, detach the clip and remove the front door weatherstrip LH.
75756D
52.REMOVE FRONT DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)
67856B
53.REMOVE FRONT DOOR PANEL PROTECTOR LH
75792
54.REMOVE DOOR WINDOW FRAME MOULDING CLIP
Detach the claw and remove the door window frame moulding clip.
Perform the following procedure only when replacement of a door window frame moulding clip in necessary.
75754A
55.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH
67864B
56.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP LH
Using a screwdriver with its tip wrapped with protective tape, detach the clip and remove the front door No. 2 weatherstrip LH.
75074
57.REMOVE FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH
58.REMOVE SCREW GROMMET
Detach the claw and remove the screw grommet.
Use the same procedure described for the other side.
59.REMOVE HOLE PLUG
Remove the hole plug.
Use the same procedure described for the other side.
67001A
60.REMOVE FRONT DOOR PANEL CUSHION
Detach the claw and remove the front door panel cushion.
Use the same procedure described for the other side.
75966B
61.REMOVE FRONT DOOR NO. 4 STRIPE LH (w/ Black Out Tape)
75986G
62.REMOVE FRONT DOOR OUTSIDE STRIPE LH (w/ Black Out Tape)
75922M
63.REMOVE NO. 1 BLACK OUT TAPE LH (w/ Black Out Tape)