Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door) › from 2020.08
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0376602 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV Model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV Model) (Click here)
Reset back door close position Power back door system (for HV Model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.

·

When performing removal for the black out tape, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD

Hide 65351A 4.REMOVE BATTERY HOLE COVER

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69278C 6.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

Hide 74646A 7.REMOVE DOOR ASSIST GRIP COVER LH

Hide 8.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 67604 9.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68174A 10.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

Hide 68199 11.REMOVE REAR DOOR REAR BELT SEAL LH

Hide 67842E 12.REMOVE REAR DOOR SERVICE HOLE COVER LH

Hide 67674A 13.REMOVE REAR DOOR FRAME GARNISH LH

Hide 68152C 14.DISCONNECT REAR DOOR GLASS RUN LH

Hide 67408E 15.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68124B 16.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

Hide 68104 17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 75722A 18.REMOVE REAR DOOR BELT MOULDING LH

Hide 67872 19.REMOVE REAR DOOR WEATHERSTRIP LH

Hide 75978H 20.REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH

HINT:

When removing the rear door lower outside stripe LH, if it is difficult to remove, heat the adhesive of the rear door lower outside stripe LH and rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Door Lower Outside Stripe LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door panel and rear door lower outside stripe LH excessively.


a.
B524069

Pull back on one of the ends of the rear door lower outside stripe LH to remove it.

HINT:

When pulling on the rear door lower outside stripe LH, pull it parallel to the rear door panel.



Hide 75988E 21.REMOVE REAR DOOR OUTSIDE STRIPE LH

HINT:

When removing the rear door outside stripe LH, if it is difficult to remove, heat the adhesive of the rear door outside stripe LH and rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Door Outside Stripe LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door panel and rear door outside stripe LH excessively.


a.
B524070

Pull back on one of the ends of the rear door outside stripe LH to remove it.

HINT:

When pulling on the rear door outside stripe LH, pull it parallel to the rear door panel.



Hide 75954A 22.REMOVE REAR INNER BLACK OUT TAPE LH

HINT:

When removing the rear inner black out tape LH, if the double-sided tape is difficult to remove, heat the adhesive of the rear inner black out tape LH and rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Inner Black Out Tape LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door panel and rear inner black out tape LH excessively.


a.
B524071

Pull back on one of the ends of the rear inner black out tape LH to remove it.

HINT:

When pulling on the rear inner black out tape LH, pull it parallel to the rear door panel.