Home › Engine / Hybrid System › M20A-FKS (COOLING) › FLOW SHUTTING VALVE (for Heater) › from 2020.08
RM3620E _51 Engine / Hybrid System _076658 M20A-FKS COOLING _0373126 FLOW SHUTTING VALVE(for Heater) A

M20A-FKS COOLING  FLOW SHUTTING VALVE(for Heater)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during flow shutting valve (water by-pass hose assembly) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline Model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 53895B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 53896B 3.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 5.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 6.DRAIN ENGINE COOLANT

Hide 16260 7.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A434847C01
0.063,0.083 0.313,0.281 0.25,0.198 10 true *A 0.063,2.521 0.333,2.719 0.271,0.198 10 true *B
*A for CVT
*B for Manual Transaxle


Disconnect the flow shutting valve (water by-pass hose assembly) connector.


b.

Disconnect the inlet heater water hose connector from the flow shutting valve (water by-pass hose assembly).

NOTICE:

Remove any foreign matter on the flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector before performing this work.


i.
A434848C01
1.552,1.823 1.729,1.823 1.729,1.823 1.927,1.313 true 1.563,4.313 1.74,4.313 1.74,4.313 1.938,3.802 true 0.031,0.052 0.313,0.25 0.281,0.198 10 true *A 0.063,2.531 0.302,2.719 0.24,0.188 10 true *B 1.354,1.729 1.583,1.896 0.229,0.167 10 true *a 1.344,4.24 1.573,4.406 0.229,0.167 10 true *a
*A for CVT
*B for Manual Transaxle
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to detach the lock claws and pull off the inlet heater water hose connector.


ii.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


iii.

Cover the disconnected inlet heater water hose connector with a plastic bag to prevent damage and contamination.



c.

Disconnect the outlet heater water hose connector from the No. 2 water by-pass pipe sub-assembly.

NOTICE:

Remove any foreign matter on the No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector before performing this work.


i.
A434849C01
1.531,1.156 1.781,1.635 1.781,1.635 1.958,1.635 true 1.542,3.615 1.792,4.094 1.792,4.094 1.969,4.094 true 0.031,0.052 0.313,0.25 0.281,0.198 10 true *A 0.063,2.531 0.302,2.719 0.24,0.188 10 true *B 2.031,1.552 2.26,1.719 0.229,0.167 10 true *a 2.031,4 2.26,4.167 0.229,0.167 10 true *a
*A for CVT
*B for Manual Transaxle
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to detach the lock claws and pull off the outlet heater water hose connector.


ii.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


iii.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.



d.
A434850C01
0.073,0.073 0.385,0.229 0.313,0.156 10 false *A 0.073,2.552 0.385,2.708 0.313,0.156 10 false *B
*A for CVT
*B for Manual Transaxle


Remove the bolt to disconnect the No. 2 water by-pass pipe sub-assembly.


e.
A434851C01
0.094,0.094 0.406,0.25 0.313,0.156 10 false *A 0.125,2.552 0.438,2.708 0.313,0.156 10 false *B
*A for CVT
*B for Manual Transaxle


Remove the bolt to disconnect the flow shutting valve (water by-pass hose assembly).


f.
A434852C01
0.073,0.042 0.281,0.219 0.208,0.177 10 true *A 0.115,2.677 0.344,2.854 0.229,0.177 10 true *B
*A for CVT
*B for Manual Transaxle


Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the water by-pass outlet sub-assembly.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and water by-pass outlet sub-assembly.