Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › MOTOR CABLE › from 2020.08
RM3620E _52 Drivetrain _076274 P710 HYBRID TRANSMISSION / TRANSAXLE _0371336 MOTOR CABLE A

P710 HYBRID TRANSMISSION / TRANSAXLE  MOTOR CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cable removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM
for A25A-FXS(w/ Canister Pump Module):

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
for A25A-FXS(w/o Canister Pump Module):

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
for A25A-FXS:

Grille shutter switch specification infomation


Vehicle control history (RoB) [X260E] is stored w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)
for A25B-FXS:

Perform Vehicle Identification Number (VIN) or frame number registration


DTC P063051 is output (Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD with NICKEL METAL HYDRIDE BATTERY:(Click here)
for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY:(Click here)
for 2WD with LITHIUM-ION BATTERY:(Click here)
for 4WD/AWD with LITHIUM-ION BATTERY:(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

for 2WD with Nickel Metal Hydride Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 4WD/AWD with Nickel Metal Hydride Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 2WD with Lithium-ion Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with LITHIUM-ION BATTERY)>PRECAUTION

for 4WD/AWD with Lithium-ion Battery:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD with LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

·

If the ECM has been struck or dropped, replace it.

·

for A25A-FXS:

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module:

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION

·

for A25B-FXS:

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



PROCEDURE

Hide G1148 2.REMOVE MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.


a.
C393915

Remove the 2 bolts and connector cover from the hybrid vehicle transaxle assembly.


b.
C393916

Detach the 2 claws to remove the terminal cap from the hybrid vehicle transaxle assembly.


c.
C393917C01
0.906,3.073 1.052,3.073 1.052,3.073 1.167,2.875 true 0.76,2.979 1,3.188 0.24,0.208 10 false *a
*a Waterproof Seal


Using an insulated tool, remove the 6 bolts and motor cable from the hybrid vehicle transaxle assembly.

NOTICE:
·

Keep the motor cable terminals and their installation area free from foreign matter, water, etc.

·

Do not touch the waterproof seal or terminals of the motor cable.

·

Cover the hole where the motor cable was installed with tape or equivalent (non-residue type) to prevent entry of foreign matter.