Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › TRANSFER CASE REAR OIL SEAL › from 2020.08
RM3620E _52 Drivetrain _077125 GF2A TRANSFER / 4WD / AWD _0416437 TRANSFER CASE REAR OIL SEAL A

GF2A TRANSFER / 4WD / AWD  TRANSFER CASE REAR OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear transfer case oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
for UB80F:

Automatic transaxle assembly


·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for K120F:

Continuously variable transaxle assembly


Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)
Front electro magnetic control clutch sub-assembly (transfer assembly) Disconnect system function check Dynamic torque vectoring AWD system (Click here)
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Transmission Jack


The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.



PROCEDURE

Hide 36100A 2.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 5.REMOVE OUTPUT SHAFT COMPANION FLANGE NUT

Hide 33309B 6.REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

Hide 36111X 7.REMOVE NO. 2 TRANSFER CASE OIL SEAL

a.
C407511C01
1.896,1.052 2.417,0.5 2.417,0.5 2.667,0.5 false 1.625,2.031 1.917,1.917 1.917,1.917 2.083,1.917 true 2.792,0.438 3.25,0.667 0.458,0.229 10 false SST 2.146,1.865 2.49,2.073 0.344,0.208 10 false *1
*1 No. 2 Transfer Case Oil Seal


Using SST, remove the No. 2 transfer case oil seal from the transfer case.

SST
09308-00010  

NOTICE:

Do not damage the No. 2 transfer case oil seal press-fit surface.



b.
C420577

Remove the spacer.


c.
C420578C01
2.073,1.208 2.583,0.917 2.583,0.917 2.75,0.917 true 2.167,3.25 2.417,2.833 2.417,2.833 2.583,2.833 true 2.667,2.76 3.063,3.083 0.396,0.323 10 false SST 2.854,0.844 3.25,1.167 0.396,0.323 10 false *1
*1 Rear Drive Pinion Bearing (Inner Race)


Using SST, remove the rear drive pinion bearing (inner race).

SST
09556-40010  


d.
C420579

Remove the transfer pinion bearing spacer.


e.

Using SST, remove the rear drive pinion bearing (outer race).

SST
09950-40011  (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09957-04010)
09506-42030  
09955-04160  

C420580C01
5.865,1.323 6.167,1 6.167,1 6.333,1 true 1.771,1.802 2.188,1.802 true 5.823,0.615 6.083,0.5 6.083,0.5 6.25,0.5 true 6.417,0.938 6.729,1.094 0.313,0.156 10 false *1 3.323,0.417 3.635,0.573 0.313,0.156 10 false *a 3.302,1.635 3.615,1.792 0.313,0.156 10 false *b 2.271,1.729 2.854,1.979 0.583,0.25 10 false SST 6.333,0.417 6.917,0.667 0.583,0.25 10 false SST
*1 Rear Drive Pinion Bearing (Outer Race) - -
*a Turn *b Hold



Hide 36111X 8.INSTALL NO. 2 TRANSFER CASE OIL SEAL

a.
C420581C01
2.188,1.677 2.604,1.677 true 1.844,3.313 2.26,3.313 true 2.365,3.24 2.948,3.656 0.583,0.417 10 false SST 2.677,1.604 3.042,1.823 0.365,0.219 10 false *1
*1 Rear Drive Pinion Bearing (Outer Race)


Using SST and a press, install the rear drive pinion bearing (outer race).

SST
09506-42020  


b.
C420579

Install a new transfer pinion bearing spacer.


c.

Temporarily install the output shaft companion flange.


d.
C420582C01
1.792,1.729 1.792,2.354 1.792,2.354 2.375,2.354 true 2.167,1.854 2.167,2.354 true 2.927,0.656 3.24,0.813 0.313,0.156 10 false *a 2.729,1.75 3.042,1.906 0.313,0.156 10 false *b 2.458,2.281 2.771,2.51 0.313,0.229 10 false SST
*a Turn
*b Hold


Using SST, install the rear drive pinion bearing (inner race).

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030)
09956-03090  


e.
C420576C01
1.802,1.729 1.802,2.333 1.802,2.333 2.469,2.333 true 2.125,1.833 2.125,2.333 true 2.521,1 2.833,1.156 0.313,0.156 10 false *a 0.854,0.51 1.167,0.667 0.313,0.156 10 false *b 2.542,2.271 2.958,2.604 0.417,0.333 10 false SST
*a Turn
*b Hold


Using SST, remove the output shaft companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030)
09956-03090  


f.
C420577

install the spacer.


g.

Apply a small amount of MP grease to the lip of a new No.2 transfer case oil seal.


h.
C407512C01
1.823,2.875 2.25,2.833 2.25,2.833 1.729,2.708 true 1.219,0.917 1.5,0.917 true 1.865,3.073 2.25,2.833 true 2.323,2.75 2.844,3.01 0.521,0.26 10 false SST 0.229,0.75 0.552,0.969 0.323,0.219 10 false (A) 1.604,0.823 1.917,0.979 0.313,0.156 10 false *1
*1 No. 2 Transfer Case Oil Seal


Using SST, install a new No. 2 transfer case oil seal to the transfer case.

SST
09554-42010  
09950-60021  (09951-01030)
09950-70010  (09951-07100)

Drive in depth (A):

3.9 to 4.9 mm (0.154 to 0.193 in.)


NOTICE:

Do not damage the No. 2 transfer case oil seal press-fit surface.


HINT:
C418050N02
0.677,1.021 0.885,1.229 0.208,0.208 10 false A

Press using the A surface.



Hide 33309B 9.INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

Hide 11.INSTALL OUTPUT SHAFT COMPANION FLANGE NUT

Hide 36100 12.REMOVE TRANSFER ASSEMBLY

Hide 36100A 13.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT