Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (for HV Model) › from 2020.08
RM3620E _53 Suspension _076490 FRONT SUSPENSION _0372230 FRONT SUSPENSION MEMBER(for HV Model) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(for HV Model)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front frame assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM
for A25A-FXS(w/ Canister Pump Module):

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
for A25A-FXS(w/o Canister Pump Module):

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
for A25B-FXS:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
for A25A-FXS:
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:(Click here)
w/o Canister Pump Module:(Click here)
for A25B-FXS:
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for HV model) (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for HV model) (Click here)
Replacement of the headlight ECU sub-assembly LH
·

Synchronize the vehicle information

·

Perform headlight ECU sub-assembly LH initialization


Lighting system (EXT) (Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist map writing


·

DTCs are output

·

EPS warning light illuminates


(Click here)

NOTICE:
·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 45319 4.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 5.DISCONNECT WIRE HARNESS

Hide 51100H 6.REMOVE FRONT FRAME ASSEMBLY

a.
C406799

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


b.
C406801

Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.


Hide 7.REMOVE FRONT STABILIZER BAR WITH BRACKET

Hide 44250 8.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY

Hide 48069 9.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C403175

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



b.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.


Hide 48068 10.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 17572B 11.REMOVE NO. 2 EXHAUST PIPE SUPPORT BRACKET

a.
C403176

Remove the 2 bolts and No. 2 exhaust pipe support bracket from the front frame assembly.