The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear upper control arm assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
| Replaced Part or Performed Procedure
|
Necessary Procedures
|
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Link
|
|
|
| Auxiliary battery terminal is disconnected/reconnected
|
Perform steering sensor zero point calibration
|
Lane control system
|
( )
|
| Parking support brake system (for HV model)*
|
| Pre-collision system
|
| Memorize steering angle neutral point
|
Parking assist monitor system
|
( )
|
| Panoramic view monitor system (for HV model)
|
( )
|
| Reset back door close position
|
Power back door system (for HV model)
|
( )
|
| Power back door initialization
|
Power door lock control system
|
( )
|
| Rear wheel alignment adjustment
|
1.
Clear zero point calibration data.
2.
Perform yaw rate and acceleration sensor zero point calibration.
|
·
ABS warning light illuminates
·
Brake warning light / yellow (minor malfunction) illuminates
·
Slip indicator light illuminates
·
VSC disabled or malfunctions
|
( )
|
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
|
·
Ultrasonic sensor detection angle
·
Ultrasonic sensor detection angle registration
|
Parking Support Brake System (for HV model)
|
( )
|
| Television camera assembly optical axis (Back camera position setting)
|
Parking Assist Monitor System
|
( )
|
·
Parking assist ECU initialization
|
Panoramic View Monitor System (for HV model)
|
( )
|
| Perform headlight ECU sub-assembly LH initialization
|
Lighting System (EXT)
|
( )
|
| Gas leak from exhaust system is repaired
|
Inspection After Repair
|
·
Engine start function, etc.
|
·
for A25A-FXS w/ Canister Pump Module:
( )
·
for A25A-FXS w/o Canister Pump Module:
( )
·
for A25B-FXS:
( )
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
| Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
|
|
| Battery terminal is disconnected/reconnected
|
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
|
Stop and start system
|
for A25A-FKS:
( )
for M20A-FKS:
( )
|
| Perform steering sensor zero point calibration
|
Lane control system
|
( )
|
| Parking support brake system (for Gasoline model)*
|
| Pre-collision system
|
| Memorize steering angle neutral point
|
Parking assist monitor system
|
( )
|
| Panoramic view monitor system (for Gasoline model)
|
( )
|
| Reset back door close position
|
Power back door system (for Gasoline model)
|
( )
|
| Power back door initialization
|
Power door lock control system
|
( )
|
| Rear wheel alignment adjustment
|
·
Perform acceleration sensor zero point calibration and store system information memorization.
|
·
VSC is disabled or malfunctions
·
Slip indicator light illuminates
·
ABS warning light illuminates
|
( )
|
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
|
·
Ultrasonic sensor detection angle
·
Ultrasonic sensor detection angle registration
|
Parking Support Brake System (for Gasoline model)
|
( )
|
| Television camera assembly optical axis (Back camera position setting)
|
Parking Assist Monitor System
|
( )
|
·
Parking assist ECU initialization
|
Panoramic View Monitor System (for Gasoline model)
|
( )
|
| Perform headlight ECU sub-assembly LH initialization
|
Lighting System (EXT)
|
( )
|
| Gas leak from exhaust system is repaired
|
Inspection After Repair
|
·
Engine start function, etc.
|
·
for A25A-FKS w/ Canister Pump Module:
( )
·
for A25A-FKS w/o Canister Pump Module:
( )
·
for M20A-FKS:
( )
|
- CAUTION:
·
If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.
·
If work is performed without wearing insulating gloves, there is a danger of electric shock.
- NOTICE:
-
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.