Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for 2WD) › from 2019.02
RM3620E _53 Suspension _076491 REAR SUSPENSION _0373102 REAR SUSPENSION MEMBER(for 2WD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for HV model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FXS w/ Canister Pump Module:

(Click here)

·

for A25A-FXS w/o Canister Pump Module:

(Click here)

·

for A25B-FXS:

(Click here)



Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FKS w/ Canister Pump Module:

(Click here)

·

for A25A-FKS w/o Canister Pump Module:

(Click here)

·

for M20A-FKS:

(Click here)



CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 58327B 3.REMOVE MAIN MUFFLER HEAT INSULATOR

Hide 53896B 4.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 5.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51420 7.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 58166A 8.REMOVE FRONT FLOOR COVER LH (w/ Floor Under Cover)

Hide 58166A 9.REMOVE FRONT FLOOR COVER RH (w/ Floor Under Cover)

Hide 58399D 10.REMOVE NO. 2 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 58398F 11.REMOVE NO. 1 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 48738C 12.REMOVE LOWER NO. 2 CONTROL ARM COVER LH (w/ Cover)

Hide 48737C 13.REMOVE LOWER NO. 2 CONTROL ARM COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the LH side.


Hide 47319F 14.SEPARATE REAR FLEXIBLE HOSE LH

a.

Remove the bolt and separate the rear flexible hose LH from the rear flexible hose bracket.


Hide 47318F 15.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 89408C 16.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

Hide 48840A 17.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 18.REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 19.REMOVE REAR STABILIZER BAR

Hide 48231B 20.REMOVE REAR COIL SPRING LH

Hide 48231A 21.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 22.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 23.REMOVE REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 24.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 25.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 26.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 27.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 28.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C403184

Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48770A 29.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 51206A 30.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C406804

Disengage the 2 clamps to separate the height control sensor wire harness.


b.
C403461C01
2.917,4.01 2.917,3.76 2.917,3.76 3,3.76 false 0.583,3.833 0.75,3.833 0.75,3.833 0.833,3.917 false 1.396,3.885 1.563,3.885 1.563,3.885 1.646,3.969 false 1.75,4.333 2.167,4.333 2.167,4.333 2.583,4.083 true 1.917,4.333 2.25,4.083 true 3.042,3.698 3.292,3.948 0.25,0.25 10 false *a 0.417,3.771 0.75,4.021 0.333,0.25 10 false *b 1.229,3.802 1.563,4.052 0.333,0.25 10 false *b 1.573,4.26 1.906,4.51 0.333,0.25 10 false *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C410424

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.



c.

Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.


d.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



e.

Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.

HINT:

Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.



Hide 48790 31.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 32.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52272A 33.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

a.
C403786C01
2.25,1.667 2.583,1.667 false 1.25,0.333 1.583,0.333 false 2.625,1.604 3.042,1.854 0.417,0.25 10 false *a 1.083,0.271 1.5,0.521 0.417,0.25 10 false *a
*a Bend Portion


Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.

NOTICE:

Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.



b.

Apply lubricant to the contact surfaces of the rear suspension member front body mounting cushion.


c.
C403787N01
0.917,1.833 1.333,1.833 true 1.917,0.604 2.25,0.271 2.25,0.271 2.417,0.271 true 2.458,0.208 2.958,0.458 0.5,0.25 10 false SST 0.604,1.771 1.021,2.021 0.417,0.25 10 true SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04010, 09952-04010, 09954-04010, 09955-04061, 09958-04011)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



d.
C403789C01
2.333,1.854 2.583,1.854 false 2.083,0.802 2.333,1.219 2.333,1.219 2.583,1.219 true 0.635,1.979 0.854,2.167 0.219,0.188 10 false *a 2.625,1.792 3.125,2.042 0.5,0.25 10 false SST 2.625,1.156 3.125,1.406 0.5,0.25 10 true SST
*a Hold
V113147

Turn


Using SST, remove the rear suspension member front body mounting cushion while applying lubricant into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04010, 09952-04010, 09954-04010, 09955-04061, 09958-04011)

NOTICE:
·

Set the claws of SST into the rear suspension member sub-assembly securely as shown in the illustration.

·

Tighten SST slowly and evenly.

·

Be careful as the rear suspension member front body mounting cushion may fly out.

·

The rear suspension member front body mounting cushion cannot be reused.




e.

Remove SST and the rear suspension member front body mounting cushion from the rear suspension member sub-assembly.


Hide 52271E 34.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 52276B 35.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

a.
C403790N01
0.833,1.875 0.833,1.635 0.833,1.635 1.135,1.635 true 0.667,1.875 1.583,1.875 true 0.833,1.75 1.583,1.75 true 2.333,2.448 2.917,2.448 true 0.344,1.813 0.927,2.063 0.583,0.25 10 false SST 2.958,2.375 3.375,2.625 0.417,0.25 10 true SST

Install SST as shown in the illustration.

SST
09950-00020  
09950-00030  
09950-60011  (09951-00330)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



b.
C403791C01
1.938,1.833 2.354,1.833 false 0.5,1.833 0.833,1.833 0.833,1.833 1.417,1.333 true 0.75,1.833 1.417,1.25 true 1.958,1.365 2.542,1.365 true 0.333,1.25 0.583,1.5 0.25,0.25 10 false *a 2.396,1.771 2.896,2.021 0.5,0.25 10 false SST 0.208,1.771 0.708,2.021 0.5,0.25 10 false SST 2.583,1.302 3.083,1.552 0.5,0.25 10 false SST
*a Hold
V113147

Turn


Using SST, remove the rear suspension member rear body mount cushion LH while applying lubricant into the clearance between the rear suspension member rear body mount cushion LH and the rear suspension member sub-assembly.

SST
09950-00020  
09950-00030  
09950-60011  (09951-00330)

NOTICE:
·

Tighten SST slowly and evenly.

·

Be careful as the rear suspension member rear body mount cushion LH may fly out.

·

The rear suspension member rear body mount cushion LH cannot be reused.




c.

Remove SST and the rear suspension member rear body mount cushion LH from the rear suspension member sub-assembly.


Hide 52275C 36.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

HINT:

Perform the same procedure as for the LH side.


Hide 37.REMOVE HOLE PLUG

a.
C403463N01
1.552,0.031 2.052,0.365 0.5,0.333 10 false A 0.51,0.281 1.01,0.615 0.5,0.333 10 false A 2.083,0.792 2.583,1.125 0.5,0.333 10 false A 3.167,0.698 3.406,0.948 0.24,0.25 10 false A 1.792,0.49 2.031,0.74 0.24,0.25 10 false B 0.99,0.198 1.229,0.448 0.24,0.25 10 false B

Remove the 6 hole plugs from the rear suspension member sub-assembly.

HINT:

There are 2 different shapes of hole plug.