Home › Steering › STEERING COLUMN › STEERING WHEEL › from 2020.08
RM3620E _55 Steering _076852 STEERING COLUMN _0377455 STEERING WHEEL A

STEERING COLUMN  STEERING WHEEL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during steering wheel assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:
(Click here)
for M20A-FKS:
(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 4.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 5.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45130 7.REMOVE HORN BUTTON ASSEMBLY

Hide 84250A 8.REMOVE STEERING PAD SWITCH ASSEMBLY

Hide 45100 9.REMOVE STEERING WHEEL ASSEMBLY

a.
C406905

Remove the steering wheel set bolt.


b.
C406907C01
1.719,1.073 2.302,0.823 2.302,0.823 1.708,1.021 true 2.375,0.75 2.688,0.906 0.313,0.156 10 true *a
*a Matchmark


Put matchmarks on the steering wheel and steering main shaft.


c.
C406909C01
2.354,1.24 2.844,0.656 2.844,0.656 1.802,0.854 true 2.885,3.688 3.198,3.844 0.313,0.156 10 true *a 0.823,3.802 1.135,3.958 0.313,0.156 10 true *b 2.896,0.573 3.354,0.771 0.458,0.198 10 true SST
*a Hold
*b Turn


Using SST, remove the steering wheel assembly.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)
09950-60011  (09951-00330)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



Hide 84610G 10.REMOVE NO. 1 TRANSMISSION SHIFT SWITCH ASSEMBLY (w/ Shift Paddle Switch)

Hide 84610H 11.REMOVE NO. 2 TRANSMISSION SHIFT SWITCH ASSEMBLY (w/ Shift Paddle Switch)

HINT:

Use the same procedure described for the No. 1 transmission shift switch assembly.