Home › Engine / Hybrid System › M20A-FKS (FUEL) › FUEL PUMP › from 2020.08
RM3620E _51 Engine / Hybrid System _076682 M20A-FKS FUEL _0376394 FUEL PUMP A

M20A-FKS FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of fuel pump Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 5.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 58325E 6.REMOVE REAR FLOOR SERVICE HOLE COVER (for LH Side)

a.

Remove the rear floor service hole cover and butyl tape.


b.
A433893

Disconnect the 2 connectors from the fuel suction pump and gauge tube assembly.


Hide 77026B 7.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A433894

Slide the clamp and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction with pump and gauge tube assembly.


Hide 77754B 8.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A433895

Detach the clamp and disconnect the charcoal canister outlet hose from the fuel suction with pump and gauge tube assembly.


Hide 9.DISCONNECT FUEL TANK EVAP TUBE SUB-ASSEMBLY

a.
A433896

Disconnect the fuel tank evap tube sub-assembly from the fuel suction with pump and gauge tube assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209C 10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A433897C01
0.417,3.823 0.583,3.823 0.583,3.823 1,3.573 true 2.188,1.771 2.729,1.354 2.729,1.354 2.896,1.354 true 0.771,1.49 1.604,1.49 true 1.917,2.917 2.417,2.5 2.417,2.5 2.583,2.5 true 0.615,2.76 0.781,2.76 0.781,2.76 1.198,2.927 true 1.552,3.531 1.885,3.531 1.885,3.531 1.885,3.667 true 1.563,3.656 2.396,3.656 true 2.927,1.271 3.167,1.438 0.24,0.167 10 true *1 0.583,1.385 0.823,1.563 0.24,0.177 10 true *2 2.615,2.406 2.927,2.563 0.313,0.156 10 false *a 0.427,2.667 0.74,2.823 0.313,0.156 10 false *b 0.24,3.729 0.552,3.885 0.313,0.156 10 false *c 2.427,3.563 2.74,3.719 0.313,0.156 10 false *d
*1 Tube Joint Clip
*2 Fuel Tank Main Tube Sub-assembly
*a Nylon Tube
*b Fuel Tube Joint
*c Plate Sub-assembly
*d O-ring
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77144 11.REMOVE FUEL PUMP GAUGE RETAINER

a.
A433898

Detach the claw to remove the No. 1 fuel tube clamp from the fuel pump gauge retainer.


b.

Remove the fuel pump gauge retainer.

i.
A433899C01
1.198,3.104 1.875,3.104 true 2.219,0.667 2.573,0.385 2.573,0.385 2.771,0.385 true 1.792,1.271 2.365,1.563 2.365,1.563 2.563,1.563 true 1.802,0.99 2.656,0.99 true 2.792,0.281 3.042,0.469 0.25,0.188 10 true *a 2.688,0.885 2.896,1.052 0.208,0.167 10 true *b 2.573,1.458 2.802,1.625 0.229,0.167 10 true *c 1.906,3 2.146,3.177 0.24,0.177 10 true *d
*a SST (Plate)
*b SST (Bolt)
*c SST (Claw)
*d Insertion Point


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01030, 09808-01050)
09808-01071  

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A434496C01
1.094,0.448 0.917,0.146 0.917,0.146 0.75,0.146 true 1.792,1.271 2.208,1.521 2.208,1.521 2.375,1.521 true 0.844,0.927 1.01,0.927 1.01,0.927 1.417,0.75 true 1.802,0.99 2.469,0.99 true 1.344,2.313 0.927,2.313 true 0.563,0.052 0.792,0.219 0.229,0.167 10 true *a 0.667,0.833 0.896,0.99 0.229,0.156 10 true *b 2.49,0.896 2.719,1.052 0.229,0.156 10 true *c 2.396,1.427 2.625,1.594 0.229,0.167 10 true *d 0.74,2.219 0.969,2.385 0.229,0.167 10 true *d
*a SST (Handle)
*b SST (Plate)
*c SST (Bolt)
*d SST (Claw)


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010)
09808-01071  


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction with pump and gauge tube assembly, remove the fuel pump gauge retainer.



Hide 77020A 12.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A434497

Disconnect the fuel return vent tube sub-assembly and remove the fuel suction with pump and gauge tube assembly from the fuel tank assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A434498

Remove the gasket from the fuel tank assembly.