Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL INJECTOR (for Port Injection) › from 2020.08
RM3620E _51 Engine / Hybrid System _076683 A25A-FKS FUEL _0373208 FUEL INJECTOR(for Port Injection) A

A25A-FKS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)
·

Replacement of port fuel injector assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


·

w/ Canister Pump Module:

(Click here)

·

w/o Canister Pump Module:

(Click here)



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 23801P 5.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A401646

Remove the fuel pipe clamp from the fuel tube connector.


b.
A401647

Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23807 7.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A401648

Remove the 2 bolts and fuel delivery pipe sub-assembly from the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



Hide 23807V 8.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A401649

Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.


Hide 23291 9.REMOVE INJECTOR VIBRATION INSULATOR

a.
A401650

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 82125N 10.REMOVE NO. 5 ENGINE WIRE

a.
A401651

Disconnect the 5 connectors from the 4 port fuel injector assemblies and fuel pressure sensor.


b.

Detach the 2 clamps and remove the No. 5 engine wire from the fuel delivery pipe sub-assembly.


Hide 23250F 11.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.
A460319

Pull the 4 port fuel injector assemblies out of the fuel delivery pipe sub-assembly.


b.
A401653

Remove the O-ring from each port fuel injector assembly.


c.
A401654N01
2,0.417 2.771,0.615 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.