1.INSTALL ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
When installing a new ultrasonic sensor retainer, heat the front bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper cover and ultrasonic sensor retainer excessively.
When reusing the front bumper cover:
Using a heat light, heat the front bumper cover surface.
Remove any remaining double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Installing the front bumper cover with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new front bumper cover surface.
| *a | Mark-off Line |
|
Primer |
Apply primer to the front bumper cover on the installation area of the ultrasonic sensor retainer using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the ultrasonic sensor retainer has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new ultrasonic sensor retainer trying not to touch the adhesional surface.
| *a | Mark-off Line |
Install the ultrasonic sensor retainer in the position shown in the illustration.
52438
2.INSTALL FRONT BUMPER GUARD COVER LH
|
Fall Prevention Hook |
Attach the fall prevention hook.
|
Install in this Direction |
Attach the claw and install the front bumper guard cover LH as shown in the illustration.
52437
3.INSTALL FRONT BUMPER GUARD COVER RH
Use the same procedure described for the LH side.
53286C
4.INSTALL FRONT BUMPER ARM HOLE COVER LH
|
Fall Prevention Hook |
Attach the fall prevention hook.
|
Install in this Direction |
Attach the claw and install the front bumper arm hole cover LH as shown in the illustration.
53285J
5.INSTALL FRONT BUMPER ARM HOLE COVER RH
Use the same procedure described for the LH side.
53113E
6.INSTALL LOWER NO. 2 RADIATOR GRILLE
|
Install in this Direction |
Attach the claw and install the lower No. 2 radiator grille as shown in the illustration.
Install the 4 screws.
52411
7.INSTALL FRONT BUMPER GUARD
|
Install in this Direction |
Attach the guide and claw to install the front bumper guard as shown in the illustration.
Install the 4 outside moulding retainers.
Install the 4 clips.
52711
8.INSTALL FRONT BUMPER MOULDING
|
Install in this Direction |
Attach the claw and guide to install the front bumper moulding as shown in the illustration.
Install the 6 outside moulding retainers.
Install the 4 clips.
53111
9.INSTALL RADIATOR GRILLE
75311
10.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
|
Install in this Direction |
Attach the claw and guide to install the radiator grille (or front panel) emblem as shown in the illustration.
Install the 2 screws.
52128B
11.INSTALL FRONT BUMPER HOLE COVER LH
|
Install in this Direction |
Attach the claw and install the front bumper hole cover LH as shown in the illustration.
52127D
12.INSTALL FRONT BUMPER HOLE COVER RH
Use the same procedure described for the LH side.
53112A
13.INSTALL LOWER RADIATOR GRILLE
|
Install in this Direction |
Attach the claw and guide to install the lower radiator grille.
Install the 2 outside moulding retainers.
53115B
14.INSTALL RADIATOR GRILLE BRACKET
|
Install in this Direction |
Attach the claw and install the radiator grille bracket as shown in the illustration.
Install the 6 screws.
|
Screw |
|
Clip (A) |
|
Clip (B) |
Install the 2 clips (B) and attach the guide.
Install the 4 clips (A).
Install the 2 screws.
53395E
15.INSTALL FRONT HOOD TO END PANEL SEAL
|
Install in this Direction |
Attach the clip and install the front hood to end panel seal.
81220
16.INSTALL FOG LIGHT ASSEMBLY LH
81210A
17.INSTALL FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
52114A
18.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET
for Type A:
|
Install in this Direction |
Attach the claw and guide to install the front bumper extension mounting bracket as shown in the illustration.
Install the 2 screws.
for Type B:
|
Install in this Direction |
Attach the guide to install the front bumper extension mounting bracket as shown in the illustration.
Install the 2 screws.
19.INSTALL NUT
|
Install in this Direction |
Install the 2 nuts.
88211B
20.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)
89347B
21.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89341L
22.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89341K
23.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
82114
24.INSTALL NO. 4 ENGINE ROOM WIRE
Attach the clamp and install the No. 4 engine room wire.
| *A | w/ TOYOTA Parking Assist-sensor System | *B | w/ Panoramic View Monitor System |
| *C | w/ Dynamic Radar Cruise Control System | - | - |
Connect each connector.