Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (except Off Road Package) › from 2020.08
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377205 FRONT BUMPER(except Off Road Package) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(except Off Road Package)  REASSEMBLY  


PROCEDURE

Hide 53112A 1.INSTALL LOWER RADIATOR GRILLE

Hide 53113E 2.INSTALL LOWER NO. 2 RADIATOR GRILLE

a.
B525550C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the lower No. 2 radiator grille as shown in the illustration.


b.
B525551

Install the 2 screws.


Hide 52711 3.INSTALL FRONT BUMPER MOULDING (for Separate Type)

a.
B525249C03
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the front bumper moulding as shown in the illustration.


b.
B526134

Install the 2 screws.


Hide 52411 4.INSTALL FRONT BUMPER GUARD

a.

Attach the claw and guide to install the front bumper guard as shown in the illustration.

B525548C01
0,0 0,0 false
V113147

Install in this Direction - -



b.
B522116

Install the 6 outside moulding retainers.


c.

Install the 2 screws.


Hide 52438 5.INSTALL FRONT BUMPER GUARD COVER LH

a.
B555211C06
0,0 0,0 false
V100135

Fall Prevention Hook


Attach the fall prevention hook and install the front bumper guard cover LH.


b.
B560724C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw.


Hide 52437 6.INSTALL FRONT BUMPER GUARD COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 53286C 7.INSTALL FRONT BUMPER ARM HOLE COVER LH

a.
B555210C06
0,0 0,0 false
V100135

Fall Prevention Hook


Attach the fall prevention hook and install the front bumper arm hole cover LH.


b.
B560726C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw.


Hide 53285J 8.INSTALL FRONT BUMPER ARM HOLE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 75311 9.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

a.
B522135C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the radiator grille (or front panel) emblem.


b.

Install the 2 screws.


Hide 52128B 10.INSTALL FRONT BUMPER HOLE COVER LH

a.

w/ Fog Light:

i.
B522134C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the front bumper hole cover LH.


ii.

Install the clip.



b.

w/o Fog Light:

i.
B525974C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the front bumper hole cover LH.


ii.

Install the clip.



Hide 52127D 11.INSTALL FRONT BUMPER HOLE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 53124B 12.INSTALL RADIATOR GRILLE SIDE MOULDING LH

a.
B522133C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the radiator grille side moulding LH.


Hide 53123B 13.INSTALL RADIATOR GRILLE SIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 53115B 14.INSTALL RADIATOR GRILLE BRACKET

a.
B525783C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the radiator grille bracket as shown in the illustration.


b.

Install the 8 screws.


c.
B525781C01
0,0 0,0 false
V100135

Screw
V100136

Clip (A)
V100137

Clip (B)


Attach the guide and install the 2 clips (B).


d.

Install the 4 clips (A).


e.

Install the 2 screws.


Hide 53395E 15.INSTALL FRONT HOOD TO END PANEL SEAL

a.
B522132C02
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and install the front hood to end panel seal.


Hide 81220 16.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 17.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 52114A 18.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET

a.

for Type A:

i.
B525553C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the front bumper extension mounting bracket as shown in the illustration.


ii.
B526276

Install the 2 screws.



b.

for Type B:

i.
B525555C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the front bumper extension mounting bracket as shown in the illustration.


ii.
B522115

Install the 2 screws.



c.

for Type C:

i.
B522115

Install the front bumper extension mounting bracket with the 2 screws.



Hide 19.INSTALL NUT

a.
B525785C01
0,0 0,0 false
V113147

Install in this Direction


Install the 2 nuts.


Hide 88211B 20.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

Hide 89347B 21.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341L 22.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 23.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89348X 24.INSTALL FRONT ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

Hide 82114 25.INSTALL NO. 4 ENGINE ROOM WIRE (w/ Wire Harness)

a.

w/o Toyota Parking Assist-sensor System:

i.

Attach the clamp and install the No. 4 engine room wire.

B525989C01
4.917,2 6.25,2 true 4.917,1.667 6.177,1.698 true 4.917,2.25 4.917,1.083 true 4.917,1.385 5.25,1.385 true 4.208,0.906 4.208,0.406 true 3.583,0.75 3.583,0.417 true 3.583,0.417 4.917,0.417 true 0.99,1.958 1.229,2.188 0.24,0.229 12 true *A 6.729,2.146 6.969,2.375 0.24,0.229 12 true *A 3.781,1.052 4.021,1.281 0.24,0.229 12 true *B 4.823,2.24 5.063,2.469 0.24,0.229 12 true *A 4.927,0.333 5.167,0.563 0.24,0.229 12 true *A
*A w/ Fog Light *B w/ Dynamic Radar Cruise Control System



ii.

Connect each connector.



b.

w/ Toyota Parking Assist-sensor System, w/o Parking Support Brake System:

i.

Attach the clamp and install the No. 4 engine room wire.

B525988C01
3.177,1.719 3.177,1.135 false 3.469,1.75 3.708,1.948 0.24,0.198 12 true *A 3.833,1.083 4.104,1.292 0.271,0.208 12 true *B 2.885,1.688 3.354,1.906 0.469,0.219 12 true *A,*B
*A w/ Panoramic View Monitor System *B w/ Dynamic Radar Cruise Control System



ii.

Connect each connector.



c.

w/ Toyota Parking Assist-sensor System, w/ Parking Support Brake System:

i.

Attach the clamp and install the No. 4 engine room wire.

B525987C01
3.49,1.719 3.76,1.958 0.271,0.24 12 true *A
*A w/ Panoramic View Monitor System - -



ii.

Connect each connector.



Hide 85271 26.INSTALL NO. 1 HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

a.

Attach the clamp and install the No. 1 headlight cleaner hose.

B526275


Hide 85208A 27.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 28.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure described for the LH side.


Hide 85354 29.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)

Hide 85353 30.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure described for the LH side.


Hide 31.INSTALL FOG LIGHT SEAL (w/o TOYOTA Parking Assist-sensor System)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When installing a new fog light seal, heat the front bumper assembly using a heat light.



Standard:
Item Temperature
Front Bumper Assembly 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the front bumper cover:

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper assembly.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the fog light seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new front bumper cover surface.





b.
B525977C01
0.917,1.417 1.417,1.417 true 0.688,1.302 0.948,1.521 0.26,0.219 10 true *a
*a Mark-off Line
V100155

Primer


Apply primer to the front bumper assembly on the installation area of the fog light seal using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the fog light seal has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new fog light seal trying not to touch the adhesional surface.


e.
B525976C01
1,1.333 1.417,1.333 true 2.354,0.802 2.771,0.802 true 0.667,1.25 0.979,1.448 0.313,0.198 10 true *a 2.719,0.708 3.031,0.906 0.313,0.198 10 true *1
*1 No. 4 Engine Room Wire
*a Mark-off Line


Install the No. 4 engine room wire in the position shown in the illustration.


f.

Install the fog light seal in the position shown in the illustration.


Hide 82821K 32.INSTALL CONNECTOR COVER (w/o Wire Harness)

a.
B525972

Attach the clamp and install the connector cover.