Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and the long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic)
  1. Air induction system
  2. Injector blockage
  3. Mass Air Flow (MAF) meter
  4. Engine Coolant Temperature (ECT) sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (for sensor 1) circuit
  8. A/F sensor (for sensor 1)
  9. A/F sensor heater (for sensor 1)
  10. Integration relay
  11. A/F sensor heater and integration relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. ECM
P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic)
  1. Injector leak or blockage
  2. MAF meter
  3. ECT sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (for sensor 1) circuit
  8. A/F sensor (for sensor 1)
  9. A/F sensor heater (for sensor 1)
  10. Integration relay
  11. A/F sensor heater and integration relay circuits
  12. ECM

HINT:
  1. When DTC P0171 or P0174 is stored, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learning value is +35% or more or -35% or less, the ECM interprets this as a fuel system malfunction.

A121607E13


MONITOR STRATEGY


Related DTCs
P0171: Fuel trim lean (bank 1)
P0172: Fuel trim rich (bank 1)
P0174: Fuel trim lean (bank 2)
P0175: Fuel trim rich (bank 2)
Required Sensors/Components (Main)
Fuel system
Required Sensors/Components (Related)
A/F sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0340 P0345 (VVT Sensor)
P0351 - P0358 (Igniter)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500 (Vehicle Speed Sensor)
Fuel system status
Closed loop
Battery voltage
11 V or more
Either of following conditions 1 or 2 set
-
1. Engine RPM
Below 1000 rpm
2. Intake air amount per revolution
0.26 g/rev or more
Catalyst monitor
Not executed

TYPICAL MALFUNCTION THRESHOLDS


Purge-cut
Executing
Either of following conditions 1 or 2 met
-
1. Average of short-term fuel trim and long-term fuel trim
35% or more (varies with ECT)
2. Average of short-term fuel trim and long-term fuel trim
-35% or less (varies with ECT)

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0171, P0172, P0174 or P0175 is output
    A
    P0171, P0172, P0174 or P0175 and other DTCs are output
    B

HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (A/F CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream ON.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the output voltages of A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    Standard:
    The A/F sensor reacts in accordance with increases and decreases in the fuel injection volume:

    +25% = Rich output:
    Less than 3.1 V

    -12.5% = Lean output:
    More than 3.4 V

    NOTICE:
    The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.


    Case
    A/F Sensor (Sensor 1) Output Voltage
    HO2 Sensor (Sensor 2) Output Voltage
    Main Suspected Trouble Area
    1
    A150787E01
    A151324E05
    A150787E01
    A150788E01
    -
    2
    A150787E01
    A150790E01
    A150787E01
    A150788E01
    1. A/F sensor
    2. A/F sensor heater
    3. A/F sensor circuit
    3
    A150787E01
    A150790E01
    A150787E01
    A150790E01
    1. Injector
    2. Fuel pressure
    3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
    1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
    2. To display the graph on the Techstream, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/ F Sensor / A/F Control System / AFS Voltage B1 S1 and O2S B1 S2 or AFS Voltage B2 S1 and O2S B2 S2; and then press the graph button on the Data List view.
    Result 
    Result
    Proceed to
    Case 1
    C
    Case 2
    B
    Case 3
    A



B
Go to step 11

C
Go to step 15
A


3.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.

  1. Read the MAF with the engine in an idling condition and at an engine speed of 2500 rpm.

    Standard:
    MAF while engine idling: Between 4.0 g/sec. and 8.0 g/sec. (shift lever: N; A/C: OFF).
    MAF at engine speed of 2500 rpm: Between 10.0 g/sec. and 20.0 g/sec. (shift lever: N; A/C: OFF).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


4.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


5.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


6.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leak .

    OK:
    No leak from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


7.CHECK FOR SPARKS AND IGNITION
A088862E01
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head (Click here).

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

    OK:
    No gas leak.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
  1. Check the injection volume (Click here).



NG
REPLACE FUEL INJECTOR (Click here)
OK


11.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E06
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12.INSPECT INTEGRATION RELAY (A/F RELAY)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the A/F fuse.

    1. Remove the A/F fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

    3. Reinstall the A/F fuse.

  1. Inspect the integration relay (A/F).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      When battery voltage not applied
      10 kΩ or higher
      When battery voltage applied to terminals 1A-2 and 1A-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY
OK


13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E14
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D19-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D20-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.



  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-1 (HA1A) - D56-22 (HA1A)
    Always
    Below 1 Ω
    D19-3 (A1A+) - D56-126 (A1A+)
    Always
    Below 1 Ω
    D19-4 (A1A-) - D56-125 (A1A-)
    Always
    Below 1 Ω
    D20-1 (HA2A) - D56-20 (HA2A)
    Always
    Below 1 Ω
    D20-3 (A2A+) - D56-103 (A2A+)
    Always
    Below 1 Ω
    D20-4 (A2A-) - D56-102 (A2A-)
    Always
    Below 1 Ω
    D19-1 (HA1A) or D56-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D19-3 (A1A+) or D56-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    D19-4 (A1A-) or D56-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    D20-1 (HA2A) or D56-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    D20-3 (A2A+) or D56-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    D20-4 (A2A-) or D56-102 (A2A-) - Body ground
    Always
    10 kΩ or higher


    A164715E03



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN

A185027E01

  1. (a) Connect the Techstream to the DLC3.
  2. (b) Turn the ignition switch to ON.
  3. (c) Turn the Techstream ON.
  4. (d) Clear DTCs (Click here).
  5. (e) Switch the ECM from normal mode to check mode using the Techstream (Click here).
  6. (f) Start the engine and warm it up with all the accessories switched OFF.
  7. (g) Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 3 to 5 minutes.

    HINT:
    If the system is still malfunctioning, the MIL will be illuminated during step (f).

    NOTICE:
    If the conditions in this test are not strictly followed, no malfunction will be detected.


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0171, P0172, P0174 or P0175 is output
    B



B
REPLACE ECM (Click here)
A

END