Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

This FFV can be used with unleaded gasoline or a combination of unleaded gasoline and E85.
E85 is a fuel with an ethanol concentration of 70 to 85% which meets the ASTM standards.
The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term (Short FT) and long-term (Long FT) fuel trims, and the alcohol concentration learned value (Alcohol Density Estimate).
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
The alcohol concentration learned value (Alcohol Density Estimate) is the estimated concentration of alcohol in the fuel as calculated by the ECM. The fuel injection volume is increased by approximately half the amount of the alcohol concentration learned value (refer to the table below for exact quantities).
However, in addition to the concentration of alcohol in the fuel, the actual A/F deviation due to malfunctions in the engine system is factored into the alcohol concentration learned value.
The fuel injection compensation amount, which is used to determine if DTCs P0171 to P0175 are stored, can be calculated by using the following formula.
Aggregate fuel trim is equal to the following: Short FT + ((1 + Long FT / 100) x (Injection Compensation Amount) - 1) x 100

Alcohol Density Estimate
0%
10%
20%
30%
40%
50%
60%
70%
80%
85%
Injection Compensation Amount
1.0
1.051
1.10
1.148
1.194
1.238
1.282
1.323
1.364
1.383
Approximation:
Aggregate fuel trim is approximately equal to the following: Short FT + ((1 + Long FT / 100) x (1 + (Alcohol Density Estimate / 2 / 100)) - 1) x 100
As an example, when the Alcohol Density Estimate is exact, the following formulas are used.
When E85 fuel is used: Aggregate fuel trim = Short FT + ((1 + Long FT / 100) x (1.383) - 1) x 100

DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic)
  1. Air induction system
  2. Injector blockage
  3. Mass Air Flow (MAF) meter
  4. Engine Coolant Temperature (ECT) sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (for Sensor 1) circuit
  8. A/F sensor (for Sensor 1)
  9. A/F sensor heater (for Sensor 1)
  10. Integration relay
  11. A/F sensor heater and integration relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. ECM
  15. Fuel pressure switching valve
  16. Fuel pressure regulator
  17. Fuel pressure regulator for high pressure
  18. Fuel pump
  19. Fuel pump ECU
P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic)
  1. Injector leak or blockage
  2. MAF meter
  3. ECT sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (for Sensor 1) circuit
  8. A/F sensor (for Sensor 1)
  9. A/F sensor heater (for Sensor 1)
  10. Integration relay
  11. A/F sensor heater and integration relay circuits
  12. ECM
  13. Fuel pressure switching valve
  14. Fuel pressure regulator
  15. Fuel pressure regulator for high pressure
  16. Fuel pump
  17. Fuel pump ECU

HINT:
  1. When DTC P0171 or P0174 is stored, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be stored. The MIL is then illuminated.


MONITOR DESCRIPTION

During air-fuel ratio feedback, if the short term fuel trim deviates from 1.0 by a large amount, the alcohol concentration learned value is updated (for example, if the short term fuel trim is more than 1.0, the alcohol concentration learned value increases), and then the short term fuel trim deviation is reflected in the long term fuel trim.
Example:
The aggregate fuel trim value is +87% or more or -35% or less, the ECM interprets this as a fuel system malfunction and stores a DTC.

A197672E01


MONITOR STRATEGY


Related DTCs
P0171: Fuel trim lean (for Bank 1)
P0172: Fuel trim rich (for Bank 1)
P0174: Fuel trim lean (for Bank 2)
P0175: Fuel trim rich (for Bank 2)
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
Mass air flow meter, Engine coolant temperature sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0351 - P0358 (Igniter)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500 (Vehicle Speed Sensor)
Fuel system status
Closed loop
Battery voltage
11 V or more
Either of following conditions 1 or 2 set
-
1. Engine speed
Below 1100 rpm
2. Intake air amount per revolution
0.36 g/rev or more
Catalyst monitor
Not executed

TYPICAL MALFUNCTION THRESHOLDS


Purge-cut
Executing
Either of following conditions 1 or 2 met
-
1. Average of the aggregate fuel trim*
87% or more (varies with ECT)
2. Average of the aggregate fuel trim*
-35% or less (varies with ECT)

HINT:
*: Aggregate fuel trim is approximately equal to the following: Short FT + ((1 + Long FT / 100) x (1 + (Alcohol Density Estimate / 2 / 100)) - 1) x 100


CONFIRMATION DRIVING PATTERN


A197675E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  5. Start the engine.

    HINT:
    After clearing the DTCs, the engine becomes difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  6. Warm it up until the ECT reaches 75 °C (167 °F) or higher [A].
  7. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more [B].

    HINT:
    Make sure that the Data List "Alcohol Density Learning" is "Compl".

  8. Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 5 minutes or more [C].

    CAUTION:
    Perform this drive pattern on a level road as much as possible and strictly observe the posted speed limits and traffic laws while driving.

    HINT:
    If the system is still malfunctioning, pending DTCs are stored during step [C].


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0171, P0172, P0174 or P0175 is output
    A
    P0171, P0172, P0174 or P0175 and other DTCs are output
    B

HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK SENSOR OUTPUT
  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or more.

  1. Connect the Techstream to the DLC3.

  1. Stop the engine.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Write down the freeze frame data.

    HINT:
    By looking at the alcohol concentration learned value, Long FT and Short FT in the freeze frame data, it is possible to determine the actual A/F deviation when a malfunction occurs.

  1. Clear the DTCs (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Flexible Fuel Vehicle.

  1. Immediately record data using snapshots.

  1. Start the engine.

    HINT:
    After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  1. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more.

    HINT:
    1. Make sure that the Data List "Alcohol Density Learning" is "Compl".
    2. If the vehicle is not driven, a long time is required before "Alcohol Density Learning" is "Compl".

  1. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.
    Result 
    Result
    Proceed to
    A/F sensor output between 3.1 and 3.4 V
    and
    O2 sensor output slowly changes in the range of 0 and 1 V
    and
    Aggregate fuel trim*1 between -20 and 65%
    C
    A/F sensor output consistently outside range of 3.1 to 3.4 V
    and
    O2 sensor output and A/F sensor output contradict each other*2
    B
    A/F sensor and O2 sensor output both consistently indicate rich or lean
    or
    Aggregate fuel trim*1 less than -20%
    or
    Aggregate fuel trim*1 more than 65%
    A

    HINT:
    1. *1: Aggregate fuel trim is approximately equal to the following: Short FT + ((1 + Long FT / 100) x (1 + (Alcohol Density Estimate / 2 / 100)) - 1) x 100
    2. *2: For example, the A/F sensor output indicates rich while the O2 sensor output indicates lean.
    3. Sensor Output Reference Values
      Air-fuel Ratio
      A/F Sensor
      HO2 Sensor
      Lean
      Higher than 3.25 V
      Below 0.4 V
      Rich
      Below 3.25 V
      Higher than 0.55 V
    4. Reference values when normal (E0 Fuel)
      AFS Voltage B1 S1
      3.28 V
      AFS Voltage B2 S1
      3.28 V
      O2S B1 S2
      0.76 V
      O2S B2 S2
      0.70 V
      Short FT #1
      1%
      Long FT #1
      -6%
      Short FT #2
      2%
      Long FT #2
      -6%
      AF Lambda B1 S1
      0.99
      AF Lambda B2 S1
      0.99
      Alcohol Density Estimate
      0%
      Alcohol Density Learning
      Compl
    5. Reference values when A/F sensor (Bank 1) is malfunctioning (E0 Fuel)
      AFS Voltage B1 S1
      4.99 V
      AFS Voltage B2 S1
      3.25 V
      O2S B1 S2
      0.95 V
      O2S B2 S2
      0.74 V
      Short FT #1
      0%
      Long FT #1
      17.1%
      Short FT #2
      0%
      Long FT #2
      -6.3%
      AF Lambda B1 S1
      1.23
      AF Lambda B2 S1
      0.99
      Alcohol Density Estimate
      41%
      Alcohol Density Learning
      Compl
    6. Reference values when air leak of the intake system (both banks are lean) (E0 Fuel)
      AFS Voltage B1 S1
      3.45 V
      AFS Voltage B2 S1
      3.56 V
      O2S B1 S2
      0.03 V
      O2S B2 S2
      0.03 V
      Short FT #1
      20.3%
      Long FT #1
      -1.6%
      Short FT #2
      19.5%
      Long FT #2
      -6.3%
      AF Lambda B1 S1
      1.04
      AF Lambda B2 S1
      1.08
      Alcohol Density Estimate
      85%
      Alcohol Density Learning
      Compl
    7. Reference values when air leak of the intake system during fuel system malfunction (actual air-fuel ratio deviation) (E85 Fuel)
      AFS Voltage B1 S1
      3.92 V
      AFS Voltage B2 S1
      3.94 V
      O2S B1 S2
      0.01 V
      O2S B2 S2
      0.01 V
      Short FT #1
      20.3%
      Long FT #1
      22.6%
      Short FT #2
      20.3%
      Long FT #2
      21.8%
      AF Lambda B1 S1
      1.20
      AF Lambda B2 S1
      1.20
      Alcohol Density Estimate
      85%
      Alcohol Density Learning
      Compl



B
Go to step 12

C
Go to step 16
A


3.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.

  1. Read the MAF with the engine in an idling condition and no load.

    Standard:
    MAF while engine idling: Between 4 g/sec. and 8g/sec. (shift lever: N; A/C: OFF; no electric load).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


4.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


5.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections .

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


6.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leak .

    OK:
    No leak from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


7.CHECK FOR SPARKS AND IGNITION
A151834
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head (Click here).

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

    OK:
    No gas leak.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FUEL LEAK
  1. Check the fuel leak .



NG
REPAIR OR REPLACE FUEL LEAKAGE POINT
OK


10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
  1. Check the injection volume (Click here).



NG
REPLACE FUEL INJECTOR (Click here)
OK


11.CHECK FUEL PRESSURE SWITCHING SYSTEM
  1. Check the Fuel Pressure Switching System (Click here).

    HINT:
    If the problem area cannot be determined by checking the fuel pressure switching system, proceed to the next step.


NEXT


12.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E06
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


13.INSPECT INTEGRATION RELAY (A/F RELAY)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the A/F fuse.

    1. Remove the A/F fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

    3. Reinstall the A/F fuse.

  1. Inspect the integration relay (A/F).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      When no battery voltage applied to terminals 1A-2 and 1A-3
      10 kΩ or higher
      When battery voltage applied to terminals 1A-2 and 1A-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY
OK


14.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E11
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D19-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D20-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.



  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-1 (HA1A) - D56-22 (HA1A)
    Always
    Below 1 Ω
    D19-3 (A1A+) - D56-126 (A1A+)
    Always
    Below 1 Ω
    D19-4 (A1A-) - D56-125 (A1A-)
    Always
    Below 1 Ω
    D20-1 (HA2A) - D56-20 (HA2A)
    Always
    Below 1 Ω
    D20-3 (A2A+) - D56-103 (A2A+)
    Always
    Below 1 Ω
    D20-4 (A2A-) - D56-102 (A2A-)
    Always
    Below 1 Ω
    D19-1 (HA1A) or D56-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D19-3 (A1A+) or D56-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    D19-4 (A1A-) or D56-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    D20-1 (HA2A) or D56-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    D20-3 (A2A+) or D56-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    D20-4 (A2A-) or D56-102 (A2A-) - Body ground
    Always
    10 kΩ or higher


    A164715E05



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


16.PERFORM CONFIRMATION DRIVING PATTERN

A197675E01

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

    HINT:
    Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.

  1. Start the engine.

    HINT:
    After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.

  1. Warm it up until the ECT reaches 75 °C (167 °F) or higher [A].

  1. Drive the vehicle at 32 km/h (20 mph) or more and maintain a constant speed for 2 minutes or more [B].

  1. Make sure that the Data List "Alcohol Density Learning" is "Compl".

  1. Drive the vehicle at between 60 and 120 km/h (38 and 75 mph), at an engine speed of between 1400 and 3200 rpm, and maintain a constant speed for 5 minutes or more [C].

    CAUTION:
    Perform this drive pattern on a level road as much as possible and strictly observe the posted speed limits and traffic laws while driving.

    HINT:
    If the system is still malfunctioning, pending DTCs are stored.


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0171, P0172, P0174 or P0175 is output
    B



B
REPLACE ECM (Click here)
A

END