Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

for Preparation Click here


SYSTEM DESCRIPTION

This circuit detects the conditions of the mirror retract switch.
The outer mirror switch sends information about the operating condition of the mirror retract switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU.

WIRING DIAGRAM


B191615E01


INSPECTION PROCEDURE

1.CHECK DTC
  1. Use the Techstream to check if the CAN communication system is functioning normally (Click here).
    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.READ VALUE USING TECHSTREAM (MIRROR RETRACT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Outer Mirror Fold SW
    Mirror retract switch signal / ON or OFF
    ON: Switch is on (retracting)
    OFF: Switch is off
    -

    OK:
    On the Techstream screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (MIRROR RETRACT FUNCTION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Body Electrical / Mirror / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Mirror 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Mirror Fold
    Mirror retract operation
    FOLD/OFF
    -
    Mirror Return
    Mirror retract operation
    RETURN/OFF
    -
    Result 
    Result
    Proceed to
    Outer rear view mirror operates normally
    A
    Outer rear view mirror LH does not operate normally
    B
    Outer rear view mirror RH does not operate normally
    C



B
Go to step 6

C
Go to step 8
A

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

4.INSPECT OUTER MIRROR SWITCH (MIRROR RETRACT SWITCH)


    B167772E05
  1. Remove the switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (MR) - 4 (E2)
    Pressed (Driving position)
    Below 1 Ω
    Not pressed
    10 kΩ or higher
    8 (MF) - 4 (E2)
    Pressed (Retracts)
    Below 1 Ω
    Not pressed
    10 kΩ or higher



NG
REPLACE OUTER MIRROR SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU AND BODY GROUND)


    B193659E02
  1. Disconnect the H1and H3 ECU connector.

  1. Disconnect the J6 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J6-4 (E2) - Body ground
    Always
    Below 1 Ω
    J6-7 (MR) - H1-9 (AMR)
    Always
    Below 1 Ω
    J6-7 (MR) - Body ground
    Always
    10 kΩ or higher
    J6-8 (MF) - H3-6 (RET)
    Always
    Below 1 Ω
    J6-8 (MF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


    B166374E02
  1. Remove the mirror LH (Click here).

  1. Check the retractable mirror's movement.

    1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery once between each mirror position check.
      2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)


    B193660E01
  1. Disconnect the M7 ECU connector.

  1. Disconnect the M5 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M5-7 (MR) - M7-1 (MR+)
    Always
    Below 1 Ω
    M5-7 (MR) - Body ground
    Always
    10 kΩ or higher
    M5-8 (MF) - M7-2 (MR-)
    Always
    Below 1 Ω
    M5-8 (MF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


    B166377E03
  1. Remove the mirror RH (Click here).

  1. Check the retractable mirror's movement.

    1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery once between each mirror position check.
      2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    B193660E02
  1. Disconnect the M7 ECU connector.

  1. Disconnect the L6 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L6-7 (MR) - M7-5 (MR+)
    Always
    Below 1 Ω
    L6-7 (MR) - Body ground
    Always
    10 kΩ or higher
    L6-8 (MF) - M7-6 (MR-)
    Always
    Below 1 Ω
    L6-8 (MF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)