Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1422/22    Compressor Lock Sensor Circuit

for Preparation Click here


DESCRIPTION

The ECM sends a engine speed signal to the air conditioning amplifier via the CAN communication system.
The air conditioning amplifier reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier determines that the compressor locks, and turns the magnetic clutch off.

DTC Code
DTC Detection Condition
Trouble Area
B1422/22
Open or short in compressor lock sensor circuit
  1. Air conditioning compressor (lock sensor)
  2. Compressor drive belt
  3. Harness or connector between air conditioning compressor (lock sensor) and air conditioning amplifier
  4. Air conditioning amplifier
  5. CAN communication system

WIRING DIAGRAM


E146212E02


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Connect the Techstream to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select "Communication Bus Check"

    OK:
    All ECUs and sensors connected to the CAN communication system are displayed.

Result 
Result
Proceed to
CAN system is normal
A
CAN system is abnormal
B


B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK AIR CONDITIONING AMPLIFIER
E124471E54
E147483E01
  1. Remove the air conditioning amplifier with the connectors still connected (Click here).

  1. Using an oscilloscope, check the waveform.
    Compressor Lock Signal 
    Terminal Name
    LOCK - SG-2
    Tester Range
    200 mV/DIV., 10 ms./DIV.
    Condition
    Engine is running
    Blower switch LO
    A/C switch ON

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC output)
    C

  1. Remove the air conditioning amplifier.



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


3.INSPECT AIR CONDITIONING COMPRESSOR (LOCK SENSOR)
E005280E27
  1. Disconnect the D39 air conditioning compressor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SSR+) - 2 (SSR-)
    20°C (68°F)
    165 to 205 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2UZ-FE)
    B
    NG (for 3UR-FE or 3UR-FBE)
    C

  1. Reconnect the air conditioning compressor connector.



B
REPLACE AIR CONDITIONING COMPRESSOR (LOCK SENSOR) (Click here)

C
REPLACE AIR CONDITIONING COMPRESSOR (LOCK SENSOR) (Click here)
A


4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING COMPRESSOR)


    E146410E02
  1. Disconnect the H24 air conditioning amplifier connector.

  1. Disconnect the D39 air conditioning compressor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H24-8 (LOCK) - D39-1 (SSR+)
    Always
    Below 1 Ω
    H24-13 (SG-2) - D39-2 (SSR-)
    Always
    Below 1 Ω
    H24-8 (LOCK) or D39-1 (SSR+) - Body ground
    Always
    10 kΩ or higher
    H24-13 (SG-2) or D39-2 (SSR-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air conditioning amplifier connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)