Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    01-DC    Transmission Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
01-DC
Transmission to component shown by sub-code failed (Detecting this DTC does not always mean actual failure)
If the same sub-code is recorded in other components, check harness for power supply and communication system of all components shown by code

HINT:
This code may be stored if the engine is started, idled for 60 seconds and then the ignition switch is turned to the start position again.

NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to clear codes stored due to the reasons described in Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The radio receiver assembly is the master unit.
  3. Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read Description before performing the following procedures.

1.CHECK FOR DTC OF OTHER COMPONENTS
  1. Check if the component shown by the sub-code is displayed in the check result of the other components.

    1. Check if "01-DC" is output for the other components.

    2. If "01-DC" is output for any other components, check if the same physical address is displayed.

      HINT:
      For the list of the components shown by sub-codes, refer to the table in the next step.

      Result 
      Result
      Proceed to
      "01-DC" is not output or the same physical address is not displayed
      A
      "01-DC" is output and the same physical address is displayed
      B



B
Go to step 4
A


2.CLEAR DTC
  1. Clear the DTCs (Click here).

    HINT:
    If "01-DC" is output for only one component, this may not indicate a malfunction.


NEXT


3.RECHECK FOR DTC
  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    Malfunction disappears.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)  

4.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


  1. Enter the diagnostic mode.


    E146440E06

  1. Press the preset switch "channel 3" to change to "Detailed Information Mode".

  1. Identify the component which has stored this code.
    Component Table 
    Component
    Physical Address
    Radio receiver assembly
    190
    "Bluetooth" handsfree module
    19D
    Satellite radio tuner*4
    1F1
    Stereo component amplifier assembly*1
    440
    Multi-media interface ECU*3
    388
    Television display assembly*2
    1B0

    1. *1: for 14 Speakers
    2. *2: w/ Rear Seat Entertainment System
    3. *3: w/ USB Audio System
    4. *4: w/ Satellite Radio

HINT:
  1. "440 (stereo component amplifier)" is the component which has stored this code in the example shown in the illustration.
  2. For details of the DTC display, refer to "DTC Check/Clear" (Click here).


NEXT


5.CHECK COMPONENT WHICH HAS STORED THIS CODE
  1. Select the component which has stored this code.

    Component Table 
    Component
    Proceed to
    Radio receiver assembly
    Radio receiver communication error (Click here)
    "Bluetooth" handsfree module
    "Bluetooth" handsfree module communication error (Click here)
    Satellite radio tuner*4
    Satellite radio tuner communication error (Click here)
    Stereo component amplifier assembly*1
    Stereo component amplifier communication error (Click here)
    Multi-media interface ECU*3
    Multi-media interface ECU communication error (Click here)
    Television display assembly*2
    Television display assembly communication error (Click here)

    1. *1: for 14 Speakers
    2. *2: w/ Rear Seat Entertainment System
    3. *3: w/ USB Audio System
    4. *4: w/ Satellite Radio


NEXT

END