Home › Drivetrain ยท A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here)



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



4. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.


    A215892E01

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.



6. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft (Click here).



7. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front exhaust pipe (Click here).



8. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C155905
  1. Remove the nut and clip, and disconnect the transmission control cable.



9. REMOVE STARTER ASSEMBLY
  1. Remove the starter (Click here).



10. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


A215546
  1. Remove the flywheel housing side cover.



    C161354
  1. Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.



11. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C112848
  1. Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.



12. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


C155908
  1. Remove the 4 bolts of the rear engine mounting insulator.



    C155907
  1. Remove the 4 nuts, 4 washers, 4 bolts and crossmember.



13. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


C155909
  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.



14. DISCONNECT WIRE HARNESS AND CONNECTOR


C155915
  1. Remove the bolt and disconnect the ground cable.



    C112849
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



  1. Disconnect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.


    C209679E01

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.

  1. Detach the 4 connector clamps and 5 harness clamps.

  1. Remove the bolt, harness clamp and disconnect the wire harness.



15. DISCONNECT WATER BY-PASS PIPE


C209353
  1. Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler to disconnect the water by-pass pipe.

    HINT:
    Use a container to catch any coolant which flows out of the water by-pass hoses.



16. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)


C209354
  1. Disconnect the 2 No. 1 transmission oil cooler hoses from the transmission.

  1. Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.

  1. Remove the 2 No. 1 transmission oil cooler hoses from the transmission oil cooler spacer.



    C209355E01
  1. Remove the 3 bolts and transmission oil cooler from the transmission oil cooler spacer.

  1. Remove the 2 O-rings from the grooves of the transmission oil cooler.



17. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)


C209356
  1. Disconnect the No. 2 transmission oil cooler inlet hose and No. 2 transmission oil cooler outlet hose from the transmission oil thermostat.

  1. Disconnect the No. 2 transmission oil cooler inlet hose and No. 2 transmission oil cooler outlet hose from the oil cooler tube, and remove them.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.



    C209357
  1. Disconnect the 2 No. 1 transmission oil cooler hoses from the transmission.

  1. Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.

  1. Remove the 2 No. 1 transmission oil cooler hoses from the transmission oil thermostat.



    C209358E01
  1. Remove the 3 bolts and oil cooler from the transmission oil thermostat.

  1. Remove the 2 O-rings from the grooves of transmission oil cooler.



18. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


C209681
  1. Remove the 10 bolts and transmission.

    NOTICE:
    Do not use excess force when prying the transmission assembly.



19. REMOVE HARNESS CLAMP BRACKET


C210207
  1. Remove the 5 bolts and 5 brackets.



20. REMOVE TRANSMISSION CONTROL CABLE BRACKET


C155906
  1. Remove the 2 bolts and bracket.



21. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


22. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch (Click here).