Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1002    Lost Communication with Gateway Module

for Preparation Click here


DESCRIPTION

  1. The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.
  2. When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

DTC Code
DTC Detection Condition
Trouble Area
U1002
Lost communication with the gateway module (MS bus).
  1. MS bus circuit
  2. Front power seat switch LH (power seat control ECU) CAN branch wire or connector
  3. Multiplex tilt and telescopic ECU CAN branch wire or connector
  4. Outer mirror control ECU assembly CAN branch wire or connector
  5. Power back door unit assembly (power back door ECU) CAN branch wire or connector*
  6. Combination meter assembly CAN main wire or connector
  7. Main body ECU (cowl side junction block LH) CAN main wire or connector
  8. Front power seat switch LH (power seat control ECU)
  9. Multiplex tilt and telescopic ECU
  10. Outer mirror control ECU assembly
  11. Combination meter assembly
  12. Main body ECU (cowl side junction block LH)
  13. Power back door unit assembly (power back door ECU)*
  14. No. 3 junction connector
  15. No. 4 junction connector*
  1. *: w/ Power Back Door System
  2. For vehicle with an seat memory.

WIRING DIAGRAM


C244516E02


C244517E02


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the CAN main wire or CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)


    C245289E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance of Malfunction
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω : Short in line
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    54 to 69 Ω
    70 Ω or higher: Open in CAN main bus line
    H37-22 (CANH) - H37-18 (B)
    Ignition switch off
    6 kΩ higher
    Below 6 kΩ : +B short
    H37-21 (CANL) - H37-18 (B)
    Ignition switch off
    6 kΩ higher
    Below 6 kΩ : +B short
    H37-22 (CANH) - H37-40 (E1)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω : Ground short
    H37-21 (CANL) - H37-40 (E1)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω : Ground short

    Text in Illustration 
    *a
    Component with harness connected
    (to Combination Meter Assembly)
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main bus line
    A
    NG (w/ Power Back Door System)
    1. Short in line
    2. +B short
    3. GND short
    B
    NG (w/o Power Back Door System)
    1. Short in line
    2. +B short
    3. GND short
    C
    OK
    D



B
Go to step 15

C
Go to step 24

D
Go to step 39
A


4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C245290E03
  1. Disconnect the H116 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-4 (CANH) - H116-15 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Power Back Door System)
    B
    NG (w/ Power Back Door System)
    C



B
Go to step 8

C
Go to step 10
A


5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C245290E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-1 (CANH) - H116-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 6
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

6.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)


    C242857E06
  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

8.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


9.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)


    C242862E03
  1. Disconnect the H2 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

10.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C242859E06
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-6 (CANH) - O41-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    C242859E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
Go to step 13
OK

REPLACE NO. 4 JUNCTION CONNECTOR 

13.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


14.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)


    C242862E03
  1. Disconnect the H2 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)


    C245289E02
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H37-40 (E1)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H37-40 (E1)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H37-18 (B)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H37-18 (B)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (to Combination Meter Assembly)



NG
Go to step 22
OK


16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)


    C242949E07
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-1 (CANH) - O42-7 (CANL)
    Ignition switch off
    200 Ω or higher
    O42-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-7 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O42-7 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 18
OK


17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    C242949E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω
    O41-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-11 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O41-11 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 20
OK

REPLACE NO. 4 JUNCTION CONNECTOR 

18.CONNECT CONNECTOR
  1. Reconnect the O41 and O42 No. 4 junction connectors.


NEXT


19.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)


    C245293E02
  1. Disconnect the O30 power back door unit assembly (power back door ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O30-6 (CANP) - O30-5 (CANN)
    Ignition switch off
    54 to 69 Ω
    O30-6 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-5 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-6 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O30-5 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Back Door Unit Assembly [Power Back Door ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (CANP, CANN)
OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (Click here)  

20.CONNECT CONNECTOR
  1. Reconnect the O41 and O42 No. 4 junction connectors.


NEXT


21.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C242953E04
  1. Disconnect the H2 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

22.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


23.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    C242750E72
  1. Disconnect the H116 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-4 (CANH) - H116-15 (CANL)
    Ignition switch off
    108 to 132 Ω
    H116-4 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-15 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-4 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H116-15 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)


    C242750E73
  1. w/o Power Back Door System:
    Disconnect the H116 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-3 (CANH) - H116-14 (CANL)
    Ignition switch off
    200 Ω or higher
    H116-3 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-3 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H116-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 29
OK


25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)


    C242750E74
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-2 (CANH) - H116-13 (CANL)
    Ignition switch off
    200 Ω or higher
    H116-2 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-13 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-2 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H116-13 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 31
OK


26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)


    C242750E75
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-5 (CANH) - H116-16 (CANL)
    Ignition switch off
    200 Ω or higher
    H116-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-16 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H116-16 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 33
OK


27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C242750E76
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-1 (CANH) - H116-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    H116-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H116-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Power Back Door System)
    A
    OK (w/o Power Back Door System)
    B
    NG
    C



B
Go to step 28

C
Go to step 35
A

REPLACE NO. 3 JUNCTION CONNECTOR 

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C242750E72
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H116-4 (CANH) - H116-15 (CANL)
    Ignition switch off
    108 to 132 Ω
    H116-4 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-15 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H116-4 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H116-15 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 37
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

29.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


30.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH LH)


    C245305E02
  1. Disconnect the X11 front power seat switch LH (power seat control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    X11-5 (CANH) - X11-1 (CANL)
    Ignition switch off
    54 to 69 Ω
    X11-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-1 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    X11-1 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Power Seat Switch LH [Power Seat Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SEAT CONTROL ECU (CANH, CANL)
OK

REPLACE FRONT POWER SEAT SWITCH LH (POWER SEAT CONTROL ECU) (Click here)  

31.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


32.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)


    C245306E02
  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H57-5 (CANH) - H57-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    H57-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H57-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANH, CANL)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

33.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


34.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)


    C245307E02
  1. Disconnect the M8 outer mirror control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-1 (CAN) - M8-21 (CGND)
    Ignition switch off
    54 to 69 Ω
    M8-1 (CAN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-21 (CGND) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-1 (CAN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    M8-21 (CGND) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Outer Mirror Control ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY (CAN, CGND)
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (Click here)  

35.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


36.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)


    C242945E06
  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

37.CONNECT CONNECTOR
  1. Reconnect the H116 No. 3 junction connector.


NEXT


38.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C242953E04
  1. Disconnect the H2 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

39.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)


  1. Connect the cable to the negative (-) battery terminal.


    C245310E02


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])
    -
    -

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the DA, DB and DD main body ECU (cowl side junction block LH) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-62 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 (ALTB) - Body ground
    Always
    11 to 14 V
    DB-13 (BECU) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)