Home › Engine / Hybrid System ยท 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P006A    MAP - Mass or Volume Air Flow Correlation Bank 1

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
P006A
After the engine is warmed up and the engine is idled for 30 seconds or more, the intake manifold pressure malfunction determination value is higher than the threshold value due to an intake leak.
(1 trip detection logic)
  1. Air induction system
  2. Mass air flow meter
  3. PCV valve and hose
  4. PCV hose connections
  5. Manifold absolute pressure sensor
  6. EGR valve
  7. ECM

MONITOR DESCRIPTION

The MIL illuminates when irregular intake manifold pressure is detected due to an intake leak.

HINT:
When the DTC is stored, the following fail-safe operations occur:
  1. Idling up is performed.
  2. VVT operation is stopped.
  3. Updating A/F learning value is prohibited.
  4. Fuel cut is prohibited.
  5. ISC flow rate is increased (ISC feedback is stopped).


MONITOR STRATEGY


Related DTCs
P006A: MAP - mass or volume air flow correlation
Required Sensors/Components (Main)
  1. MAP sensor
  2. ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Time after engine start
5 seconds
Engine coolant temperature
70°C (158°F) or higher
Intake air temperature
5.5°C (41.9°F) or higher
Atmospheric pressure
76 kPa (570 mmHg) or higher
Engine load fluctuation (per 8 msec.)
10% or less
VVT system
Stable
EGR valve
Closed
Engine speed
250 to 2000 rpm
Engine load (normal operation)
35% or less
Engine load (fail-safe)
41% or less

TYPICAL MALFUNCTION THRESHOLDS


Pressure correlation
24 kPa (180 mmHg) or higher

CONFIRMATION DRIVING PATTERN


A213995E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with the A/C switch and all accessory switches off and the shift lever in P or N.
  7. Idle the engine for 30 minutes or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P006A.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

  1. Drive the vehicle at 60 km/h (37 mph) for 5 minutes or more.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  1. Idle the engine for 30 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    DTC P006A is output
    A
    DTC P006A and other are output
    B

    HINT:
    If any DTCs other than P006A are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE (HOSE CONNECTION)
  1. Check the PCV hose connections .

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


3.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks .

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


4.READ VALUE USING TECHSTREAM (MAP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.

  1. Read the MAP value.

    Standard:
    Engine Condition
    Techstream Display
    Ignition switch ON
    85 to 110 kPa (638 to 825 mmHg, 25 to 32 in.Hg)

    HINT:
    Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m increase in altitude, pressure drops by 1 kPa (0.01 kgf/cm2, 0.15 psi). Varies by weather (high atmospheric pressure, low atmospheric pressure).
    Also, check "Atmosphere Pressure" in the Data List.



OK
Go to step 6

NG
Go to step 5

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor. (Click here).


NEXT


6.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    1. When performing the Active Test, make sure the shift lever is in P or N.
    2. The A/C switch and all accessory switches should be off.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.

    OK:
    MAP and idling condition change in response to EGR step position as follows.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stall
    MAP
    (Data List)
    20 to 40 kPa (150 to 300 mmHg, 6 to 12 in.Hg)
    MAP value is at least +10 kPa (75 mmHg, 3 in.Hg) higher than when EGR valve is fully closed



OK
Go to step 8

NG
Go to step 7

7.INSPECT EGR VALVE
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve assembly is stuck open.

    OK:
    EGR valve is tightly closed.



NG
REPLACE EGR VALVE (Click here)
OK


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P006A)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear the DTC (Click here).

  1. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off.

    HINT:
    The A/C switch and all accessory switches should be off, and the shift lever should be in N or P.

  1. Idle the engine for 30 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    DTC P006A is output
    A
    DTC is not output
    B



B
END
A


9.INSPECT MASS AIR FLOW METER
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off, and the shift lever should be in N or P.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List /All Data / MAF.

  1. Check MAF in the Data List during idling.

    Standard:
    3.4 to 6.2 gm/s



NG
REPLACE MASS AIR FLOW METER (Click here)
OK

REPLACE ECM (Click here)