DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |
DTC P0305 Cylinder 5 Misfire Detected |
DTC P0306 Cylinder 6 Misfire Detected |
DTC P0307 Cylinder 7 Misfire Detected |
DTC P0308 Cylinder 8 Misfire Detected |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 P0305 P0306 P0307 P0308 | Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
|



| Engine RPM | Duration |
| Idling | 3.5 minutes or more |
| 1000 | 3 minutes or more |
| 2000 | 1.5 minutes or more |
| 3000 | 1 minute or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 are output | A |
| P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 3.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections.
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.
Read the value displayed on the intelligent tester.
| Data List | Tester Display | Proceed to |
| Catalyst OT MF F/C | AVAIL (Avail) | A |
| NOT AVL (Not Avl) | B |
|
| ||||
| A | |
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.
Perform the Active Test.
| NEXT | |
| 6.READ VALUE USING INTELLIGENT TESTER (MISFIRE COUNT) |
Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count, #2, #3, #4, #5, #6, #7 and #8.
Allow the engine to idle.
Read each value for Cylinder #1 Misfire Count to #8 displayed on the intelligent tester. If no misfire counts occur in any cylinders, perform the following procedures:
Move the shift lever to D.
Check the Cylinder #1 Misfire Count to #8.
If misfire counts are still not displayed, perform procedure "A" and "B" and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read value using intelligent tester (Misfire RPM and Misfire Load)" procedures above (Procedure "A").
Read the Cylinder #1 Misfire Count to #8 or DTCs displayed on the intelligent tester (Procedure "B").
| Result | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 7.INSPECT SPARK PLUG |
![]() |
Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).
Measure the spark plug electrode gap.
Check the electrode for carbon deposits.
| Manufacturer | Product |
| DENSO | SK20HR11 |
|
| ||||
| OK | |
| 8.CHECK FOR SPARKS AND IGNITION |
![]() |
Disconnect the injector connectors to prevent the engine from starting.
Remove the ignition coil from the cylinder head (Click here).
Install the spark plug onto the ignition coil.
Attach the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check the spark.
Install the ignition coil.
Reconnect the injector connectors.
|
| ||||
| OK | |
| 9.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D56-86 (#10) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-109 (#20) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-85 (#30) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-108 (#40) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-84 (#50) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-107 (#60) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-83 (#70) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-106 (#80) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER |
Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).
|
| ||||
| OK | |
| 12.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage .
|
| ||||
| OK | |
| 13.CHECK VALVE TIMING |

Remove the cylinder head cover LH and RH.
Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.
Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.
|
| ||||
| OK | |
| 14.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 15.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 16.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition.
|
| ||||
| OK | ||
| ||
| 17.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage .
|
| ||||
| OK | |
| 18.CHECK VALVE TIMING |

Remove the cylinder head cover LH and RH.
Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.
Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.
|
| ||||
| OK | |
| 19.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 20.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 21.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition.
|
| ||||
| OK | |
| 22.INSPECT SPARK PLUG |
![]() |
Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).
Measure the spark plug electrode gap.
Check the electrode for carbon deposits.
| Manufacturer | Product |
| DENSO | SK20HR11 |
|
| ||||
| OK | |
| 23.CHECK FOR SPARKS AND IGNITION |
![]() |
Disconnect the injector connectors to prevent the engine from starting.
Remove the ignition coil from the cylinder head (Click here).
Install the spark plug onto the ignition coil.
Attach the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check the spark.
Install the ignition coil.
Reconnect the injector connectors.
|
| ||||
| OK | |
| 24.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 25.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D56-86 (#10) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-109 (#20) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-85 (#30) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-108 (#40) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-84 (#50) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-107 (#60) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-83 (#70) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
| D56-106 (#80) - D56-43 (E01) | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 26.CHECK FUEL INJECTOR OF MISFIRING CYLINDER |
Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).
|
| ||||
| OK | ||
| ||
| 27.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed spark plug to a spark plug that functions normally.
Perform a spark test.
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the injector connector.
Ground the spark plug.
Check if sparks occur while the engine is being cranked.
|
| ||||
| OK | ||
| ||
| 28.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER |
Change the ignition coil to an ignition coil that functions normally.
Perform a spark test.
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the injector connector.
Ground the spark plug.
Check if sparks occur while the engine is being cranked.
|
| ||||
| OK | ||
| ||