Display Function
Symptom
| Suspected Area
| See page
|
Pressing ignition switch does not turn on system.
| Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Black screen (No image appears on navigation/audio screen).
| Proceed to "Black Screen"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Display does not dim (does not change to night screen) with tail switch on.
| Proceed to "Display does not Dim when Light Control Switch is Turned ON"
|
Click here
|
Proceed to "Illumination Circuit"
|
Click here
|
Meter / gauge system
|
Click here
|
Navigation receiver assembly
|
Click here
|
Power does not turn off (Screen remains on).
| Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen is distorted.
| Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen flicker or color distortion.
| Proceed to "Screen Flicker or Color Distortion"
|
Click here
|
Proceed to "Navigation Receiver Assembly Power Source Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Navigation function switches can be operated while vehicle being driven.
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Navigation Function
Symptom
| Suspected Area
| See page
|
GPS mark is not displayed.
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Date and time on navigation screen is different from actual date and time.
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark deviates from correct position and does not return to correct position.
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Cursor or map rotates when vehicle is stopped.
| Proceed to "Cursor or Map Rotates when Vehicle Stopped"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark moves in the opposite direction to the vehicle.
| Proceed to "Cursor or Map Rotates when Vehicle Stopped"
|
Click here
|
Proceed to "Reverse Signal Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark deviates from and returns to correct position repeatedly even though GPS mark is displayed.
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Drive the vehicle for sensor learning (At a place where GPS signals can be received, drive the vehicle clockwise and counterclockwise in at least a 200 meter square 2 times or more)
| -
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Vehicle position mark moves slow or fast.
| Proceed to "GPS Mark is not Displayed"
|
Click here
|
Navigation antenna assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Voice guidance does not function.
| Proceed to "Voice Guidance does not Function"
|
Click here
|
Proceed to "Speaker Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Map display is incomplete.
| SD card
| -
|
Navigation receiver assembly
|
Click here
|
Route cannot be calculated.
| Proceed to "Route cannot be Calculated"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Navigation system cannot record memory point registration or each item setting.
| Navigation receiver assembly
|
Click here
|
A message indicating to wait for a while because of low temperature is displayed.
| Start the engine and increase cabin temperature (Near navigation receiver assembly)
| -
|
Navigation receiver assembly
|
Click here
|
A message is displayed because map data cannot be read, and current position screen is not displayed.
| If message appears only when driving on rough roads, check if message disappears when vehicle is stopped
| -
|
SD card
| -
|
Navigation receiver assembly
|
Click here
|
Map screen turns white or blue (GPS receiving status is displayed normally, and switches and own vehicle position mark are also displayed normally).
| Change map scale to smallest (a scale that shows a large area)
| -
|
SD card
| -
|
Navigation receiver assembly
|
Click here
|
The password set using the memory point export/ import function has been forgotten.
| Proceed to "Clear Backup Password of Export/ Import Memory Point Function" in Operation Check
|
Click here
|
Reverse signal does not change in vehicle signal check mode.
| Proceed to "Reverse Signal Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Parking brake switch signal does not change in vehicle signal check mode.
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
FM or AM Radio Function
Symptom
| Suspected Area
| See page
|
Radio broadcast cannot be received or poor reception.
| Proceed to "Radio Broadcast cannot be Received or Poor Reception"
|
Click here
|
Radio broadcast can be received but radio station cannot be displayed (Some radio stations do not provide their name information).
| Navigation receiver assembly
|
Click here
|
Radio broadcast can be displayed but radio broadcast cannot be heard from speakers.
| Check the volume settings
| -
|
Navigation receiver assembly
|
Click here
|
Radio broadcast can be received but station list cannot be displayed.
| Wait for 120 seconds in radio mode, and select the "Refresh" switch on the station list screen
| -
|
Navigation receiver assembly
|
Click here
|
Radio broadcast can be received but station list cannot be displayed.
| Select the "Refresh" switch on the station list screen
| -
|
Wait for 10 minutes with the ignition switch ACC, and select the "Refresh" switch on the station list screen again
| -
|
Navigation receiver assembly
|
Click here
|
After the voice recognition function or hands-free function is turned off, the cache radio does not operate.
| Check that the cache radio setting is on
| -
|
Navigation receiver assembly
|
Click here
|
When the cache radio is playing, sound is interrupted, sound cannot be heard or sound quality is poor.
| Check if similar symptoms occur when receiving conventional FM/AM radio broadcasts
| -
|
Check if similar symptoms occur when receiving other broadcasts
| -
|
Move the vehicle to a place where the reception sensitivity is good and check again
| -
|
Navigation receiver assembly
|
Click here
|
When the cache radio is playing, sound can be heard, but no information is displayed (some radio stations do not provide their name information).
| Check if similar symptoms occur when receiving other broadcasts
| -
|
Move the vehicle to a place where the reception sensitivity is good and check again
| -
|
Navigation receiver assembly
|
Click here
|
CD or DVD Player Function
Symptom
| Suspected Area
| See page
|
Disc cannot be played or player does not function with disc.
| Proceed to "Disc Player Outline" in System Description and check if the disc is compatible with the disc player
|
Click here
|
Navigation receiver assembly
|
Click here
|
Disc cannot be inserted/played or disc is ejected right after insertion.
| Proceed to "Disc cannot be Inserted or is Ejected Right After Insertion"
|
Click here
|
Disc cannot be ejected.
| Proceed to "Disc cannot be Ejected"
|
Click here
|
Disc sound skips.
| Proceed to "CD/DVD Sound Skips"
|
Click here
|
While vehicle is stopped, DVD cannot be viewed even when parking brake is set (parking brake switch is on).
| Proceed to "Parking Brake Switch Circuit"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Screen color is poor only when watching a DVD.
| Change the color settings on the screen adjustment screen
| -
|
Navigation receiver assembly
|
Click here
|
Sound quality is bad only when disc is played (volume is too low).
| Proceed to "Sound Quality is Bad Only when Disc is Played (Volume is Too Low)"
|
Click here
|
When disc is playing, cover art cannot be displayed.
| Navigation receiver assembly
|
Click here
|
Album cover art cannot be displayed.
| Check that Display Cover Art on the disc settings screen is set to on
| -
|
Check if similar symptoms occur with another vehicle
| -
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" Hands-free Function
Symptom
| Suspected Area
| See page
|
"Bluetooth" is inoperative (In-vehicle device cannot be recognized by the cellular phone).
| Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" compatible cellular phone cannot be registered.
| Proceed to "Cellular Phone Registration Failure"
|
Click here
|
"Bluetooth" compatible cellular phone cannot be connected.
| Check that no other cellular phone is connected as a hands-free device
| -
|
Bring the cellular phone near the in-vehicle device and reconnect it
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" compatible cellular phone cannot be connected automatically (can be connected manually).
| Check that "Bluetooth" automatic connection setting of the in-vehicle device is on
| -
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" compatible cellular phone connection is disconnected.
| Bring the cellular phone near the in-vehicle device and check if it is reconnected
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
When the ignition switch is turned to ACC, instructions for checking the connection condition between the in-vehicle device and cellular phone are displayed.
| Turn the cellular phone connection conformation display on the in-vehicle device off
| -
|
Phonebook data cannot be transferred.
| Check that the phonebook automatic transfer setting of the in-vehicle device is on
| -
|
Enter "1234" into the "Bluetooth" phone (when transferring phonebook data, OBEX authentication may be required)
| -
|
Check that no applications on the cellular phone are running
| -
|
If using "Bluetooth" audio function, cancel the "Bluetooth" audio player connection and check the operation
| -
|
Transfer phonebook data manually
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Phonebook data is cleared.
| Navigation receiver assembly
|
Click here
|
Phonebook data cannot be edited.
| Check that the phonebook data automatic transfer setting is off
| -
|
Navigation receiver assembly
|
Click here
|
All the transferred phonebook data is sorted to "Other".
| Check that no applications on the cellular phone are operating
| -
|
Check that phonebook data in the cellular phone is not stored to the SIM card
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Explain to the customer that all the transferred phonebook data may be stored to "Other" depending on cellular phone
| -
|
Cellular phone cannot make outgoing/ incoming calls.
| Move the vehicle into a cellular phone service area, check that the "Bluetooth" device is connected to the vehicle and operate device again
| -
|
Check that the cellular phone can make outgoing/incoming calls properly when not connected via "Bluetooth"
| -
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Other caller's voice is interrupted by noise or sound quality is poor.
| Check the receiving voice volume (if it is too high, voice may sound distorted)
| -
|
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Other caller's voice cannot be heard.
| Check that reception voice volume is not set to minimum
| -
|
Make a call with the cellular phone disconnected from "Bluetooth" and check that other caller's voice can be heard clearly
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Caller's voice (your voice) is interrupted by noise or sound quality is poor.
| Check the transmitting voice volume (if it is too high, voice may sound distorted)
| -
|
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence)
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Proceed to "Microphone Circuit between Microphone and Navigation Receiver Assembly"
|
Click here
|
Other caller cannot hear your voice.
| When talking on the cellular phone, check that the mute button is not pressed
| -
|
Check that nothing can cause noise around the microphone (an outlet of the air conditioning system facing the microphone, wind from an open window, additional devices, etc. may affect noise occurrence)
| -
|
Proceed to "Check Hands-free Voice Quality Setting" in Operation Check
|
Click here
|
Proceed to "Cellular Phone Inspection"
|
Click here
|
Proceed to "Microphone Circuit between Microphone and Navigation Receiver Assembly"
|
Click here
|
"Bluetooth" Audio Function
Symptom
| Suspected Area
| See page
|
Portable player cannot be registered.
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player cannot be connected manually/automatically.
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Proceed to "Portable Player cannot be Connected Manually/Automatically"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Cellular phone with portable audio function cannot be recognized as "Bluetooth" audio device even when connected using "Bluetooth".
| Proceed to "Portable Player cannot be Registered"
|
Click here
|
Proceed to "Portable Player cannot be Connected Manually/Automatically"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Sound of portable player cannot be heard from speakers, or sound is low.
| Proceed to "Sound of Portable Player cannot be Heard from Speakers or Sound is Low"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player does not play even after "Bluetooth" audio mode is selected.
| Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player does not play.
| Proceed to "Does not Play even after Bluetooth Audio Mode is Selected"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Track information such as track number, track name, elapsed play time and playlist is not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Operation switches for portable player such as play, pause, repeat, random and scan are not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Battery condition of portable player is not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
"Bluetooth" signal condition is not displayed.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Portable player cannot pause, select file, fast forward, fast rewind, play at random or scan.
| Proceed to "Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Noise occurs or sound skips when portable player plays.
| Proceed to "Noise Occurs or Sound Skips when Portable Player Plays"
|
Click here
|
Navigation receiver assembly
|
Click here
|
Registered device cannot be deleted.
| Proceed to "Registered Device cannot be Deleted"
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB Audio System Function
Symptom
| Suspected Area
| See page
|
USB audio system sound cannot be heard or sound quality is bad (USB connector is used).
| Proceed to "Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB device or "iPod" is not recognized.
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Track information such as track, artist and album names are not displayed.
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
USB device or "iPod" is recognized but cannot play, or can play but not in a sorted order.
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Album cover art cannot be displayed.
| Check that Display Cover Art on the "iPod" or USB Settings screen is set to
| -
|
Check if similar symptoms occur with another vehicle
| -
|
Navigation receiver assembly
|
Click here
|
User set album cover art cannot be displayed.
| Check that a JPEG file is used for the album cover art registered to the music data in the USB device or "iPod" - Navigation receiver assembly
| -
|
Navigation receiver assembly
|
Click here
|
"iPod" battery cannot be charged.
| Proceed to "USB Audio System Recognition/Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Customize Startup Image or Screen Off Image Function
Symptom
| Suspected Area
| See page
|
Screen cannot be changed to UIC setting screen.
| Navigation receiver assembly
|
Click here
|
Thumbnails for opening image setting or screen off image setting do not update when USB device is connected.
| Check that the USB device was not disconnected while transferring an image
| -
|
Check that the screen was not changed to another function menu while transferring an image
| -
|
Proceed to "USB Audio System Recognition/ Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Transfer button cannot be pressed.
| Check that a USB device is connected
| -
|
Check that the USB device is not in use (USB audio system is playing etc.)
| -
|
Proceed to "USB Audio System Recognition/ Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Image data in USB device cannot be displayed.
| Check that the designated folder name is used
| -
|
Check that the file extension of the data is JPG or JPEG
| -
|
Check that the file name is 32 characters or less and available language is used
| -
|
Check that the image data size is 10 MB or less
| -
|
Check that the file system of the USB device is FAT16 or FAT32
| -
|
Proceed to "USB Audio System Recognition/ Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Set opening image or screen off image is not displayed.
| Check if it is the first start-up after disconnecting and reconnecting the +B terminal (reading from the SD card may be slow when the system is first starting-up)
| -
|
Set the opening image or screen off image again
| -
|
Navigation receiver assembly
|
Click here
|
Stored image cannot be deleted.
| Navigation receiver assembly
|
Click here
|
Message indicating that USB device cannot be accessed is displayed.
| Check that the USB device has not been disconnected while the navigation system is recognizing it
| -
|
Proceed to "USB Audio System Recognition/ Play Error"
|
Click here
|
No. 1 stereo jack adapter assembly
|
Click here
|
Navigation receiver assembly
|
Click here
|
Thumbnail images for opening image or screen off image are not displayed on setting screen.
| Check if it is the first start-up after disconnecting and reconnecting the +B terminal (reading from the SD card may be slow when the system is first starting-up)
| -
|
Set the opening image or screen off image again
| -
|
Navigation receiver assembly
|
Click here
|
Image cannot be set for opening image or screen off image on setting screen.
| Set the opening image or screen off image again
| -
|
Navigation receiver assembly
|
Click here
|