DTC P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1 |
DTC P2441 Secondary Air Injection System Switching Valve Stuck Close Bank1 |
DTC P2442 Secondary Air Injection System Switching Valve Stuck Open Bank 2 |
DTC P2443 Secondary Air Injection System Switching Valve Stuck Closed Bank 2 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2440 P2442 | Pressure sensor detects pulsation of exhaust gas despite ECM commanding Air Switching Valve (ASV) to close, while engine running (1 trip detection logic) |
|
| P2441 P2443 | Pressure sensor detects no pulsation of exhaust gas despite ECM commanding Air Switching Valve (ASV) to open, while engine running (2 trip detection logic) |
|
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Close |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 2.4 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Close |
| Pressure | Less than 2.4 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Detected Condition while AIR Operating: Air Pump ON, ASV Open | Detected Condition while AIR not Operating: Air Pump OFF, ASV Closed | ECM Determination | DTC Output |
| Case 1 | Case 8 | Normal | - |
| Case 1 | Case 6 | ASV stuck open | P2440 or P2442 |
| Case 1 | Case 7 | Air pump stuck ON | P2444 or P2446 |
| Case 2 | Case 8 | Air pump stuck OFF | P2445 or P2447 |
| Case 3 | Case 8 | ASV stuck closed | P2441 or P2443 |
| Case 1 | Case 5 | ASV stuck open and air pump stuck ON | P2440 and P2444 or P2442 and P2446 |
| Case 2 | Case 6 | ASV stuck open and air pump stuck OFF | P2440 and P2445 or P2442 and P2447 |
| Case 3 | Case 7 | ASV stuck closed and air pump stuck ON | P2441 and P2444 or P2443 and P2446 |
| Case 4 | Case 8 | ASV stuck closed and air pump stuck OFF | P2441 and P2445 or P2443 and P2447 |
| Tester Operation | Air Pump | ASV | Pressure*1 | Pulsation*2 |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 2.4 kPa or more | 20 kPa or more |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Less than 2.4 kPa | Less than 30 kPa |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P2440, P2441, P2442 and/or P2443 are output | A |
| P2440, P2441, P2442 and/or P2443 and P0412 and/or P0415 are output | B |
| P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412 and P0415) are output | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
![]() |
Visual check
Start the engine and warm it up.
Turn the ignition switch off.
Disconnect the No. 1 air hose.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN.
Start the engine.
Perform the AIR system intrusive operation while the engine is idling.
Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned ON.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: ON, ASV1: CLOSE, AIR PUMP 2: ON, ASV2: CLOSE.
Check that the exhaust gas does not pulsate when the ASV is turned OFF.
Turn the ignition switch off.
| Air Pump Operation | ASV Operation | Exhaust Gas Pulsation |
| ON | OFF | Not detected |
| ON | ON | Detected |
Other inspection method:
The ASV operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.
Perform System Check operation under Manual Mode.
*: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
Start the engine after the intelligent tester initialization is finished.
Perform the AIR system intrusive operation while the engine is idling.
Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the intelligent tester indicate the conditions shown in the table below.
Turn the ignition switch off.
| AIR System Operation | Pulsation Condition (ECM Calculation) | Air-Fuel Ratio (Reference) |
| AIR PUMP: ON, ASV: OPEN | 20 kPa or more | 18 or more |
| AIR PUMP: OFF, ASV: CLOSE | Less than 30 kPa | Approximately 14.5 (around stoichiometric air-fuel ratio) |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.INSPECT AIR TUBE (BLOCKAGES AND LEAK) |
![]() |
Check that the No. 2 and No. 3 air tubes are securely connected to both the exhaust manifold and the ASV.
Inspect the air tube for blockages and damage.
|
| ||||
| OK | |
| 4.INSPECT AIR SWITCHING VALVE |
Inspect the air switching valve (Click here).
|
| ||||
| OK | |
| 5.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the AID connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D31-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D32-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
| D33-1 (BAT2) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D34-5 (+B2) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D32-1 (E) - Body ground | Always | Below 1 Ω |
| D34-1 (E2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the ECM connector.
Disconnect the AID connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D56-28 (AIRV) - D32-3 (SIV) | Always | Below 1 Ω |
| A27-43 (ARV2) - D34-3 (SIV2) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 7.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (if set) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Automatic Mode.
Start the engine after the intelligent tester initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||
| 9.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR) |
|
| ||||
| OK | |
| 10.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR) |
![]() |
Connect a pressure gauge to the air pressure sensor as shown in the illustration.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute) and Air Pump2 Pressure (Absolute).
Check that the pressure displayed on the intelligent tester fluctuates when applying the pressure to the pressure sensor with the pressure gauge.
|
| ||||
| OK | ||
| ||