Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1745    Exhaust Solenoid Valve Circuit Malfunction

for Preparation Click here


DESCRIPTION

The suspension control ECU operates the exhaust solenoid valve (height control compressor), releases the air from the height control cylinder assembly (pneumatic cylinder), and lowers vehicle height.
When the vehicle height is lowered, the suspension control ECU opens the height control valve and then operates the exhaust solenoid valve to release the compressed air to the outside.
The exhaust solenoid valve is on the compressor unit and has only one valve.

DTC Code
Detection Condition
Trouble Area
C1745
When either of the following is detected:
  1. With the exhaust valve not activated, an open signal of the exhaust valve is detected for 1 second or more.
  2. With the exhaust valve activated, a short signal of the exhaust valve is detected 8 times successively.
  1. Wire harness or connector
  2. Exhaust solenoid valve (No. 1 height control compressor)
  3. Suspension control ECU

HINT:
  1. Once the ECU stores DTC C1745 in the memory, the vehicle height control is suspended until a normal signal is input to the ECU from the exhaust solenoid valve. However, control is resumed if the ignition switch is turned off, then to ON again.
  2. Malfunction in the exhaust solenoid valve:
    The height control indicator light "N" comes on or blinks, and "HI" and "LO" do not come on by operating the height control switch "UP" or "DOWN".


WIRING DIAGRAM


C179528E04


INSPECTION PROCEDURE

NOTICE:
After replacing the suspension control ECU, perform registration (Click here).

HINT:
  1. If DTC C1781 (ECU malfunction) and/or C1782 (power source circuit) is displayed, perform the inspection necessary for DTC C1781 (Click here) and/or C1782 (Click here) first.
  2. If DTC C1781 and the C1782 are output at the same time, perform the inspection necessary for DTC C1782 first.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (EXHAUST SOLENOID)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Exhaust Solenoid
    Exhaust solenoid valve
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC Chart)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.INSPECT NO. 1 HEIGHT CONTROL COMPRESSOR (EXHAUST SOLENOID VALVE)


    C165645E03
  1. Turn the ignition switch off.

  1. Disconnect Q3 solenoid valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    10 to 14 Ω

  1. Connect the battery positive (+) lead to terminal 1 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve makes an operating sound.

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 1 HEIGHT CONTROL COMPRESSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (EXHAUST SOLENOID VALVE - ECU AND BODY GROUND)


    C241566E02
  1. Disconnect the O18 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q3-1 - O18-9 (SLEX)
    Always
    Below 1 Ω
    Q3-1 or O18-9 (SLEX) - Body ground
    Always
    10 kΩ or higher
    Q3-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)